6.3.2 When and where to carry it out ......................................271
6.3.3 Interval - 10 hours ............................................... 276
6.3.3.1 Hydraulic and hydrostatic systems tank (1) ....................... 276
6.3.3.2 Engine oil (2) .............................................277
6.3.3.3 Threshing drum variator (3) ...................................278
6.3.3.4 Coolant expansion tank (4) ...................................278
6.3.3.5 Prefilter/water separator (5) .................................. 279
6.3.3.6 Straw chopper rotor (6) ..................................... 279
6.3.4 Interval - 50 hours ............................................... 280
6.3.4.1 Rear axle support (11) ...................................... 280
6.3.4.2 Table drive-belt tensioner (12) ................................ 280
6.3.4.3 Service brakes (13) ........................................ 281
6.3.4.4 Cab air filters (14) ......................................... 281
6.3.4.5 Fanning mill variator (15) .................................... 283
6.3.4.6 Coupling bushes of final drive shafts (16) ........................ 283
6.3.4.7 Rear-axle king pins (17) ..................................... 284
6.3.4.8 Evaporator (18) ........................................... 284
6.3.4.9 Condenser (19) ........................................... 285
6.3.4.10 Engine radiator and hydraulic oil radiator (20) .....................286
6.3.4.11 Adjusting the rotary screen brushes and aspirator brushes ...........287
6.3.4.12 Grain-tank filling auger gearbox (21) ........................... 288
6.3.4.13 Track frames (22) .........................................289
6.3.4.14 Rear straw walker shaft supports (23) ......................... 290
6.3.5 Interval - 100 hours ...............................................291
6.3.5.1 Unloading auger bottom gearbox (31) ...........................291
6.3.5.2 Crop-unloading auger drive belt tensioner (32) .....................292
6.3.5.3 Main crop-elevator belt tensioner (33) ...........................292
6.3.5.4 Chaff spreader drive (if installed) (34) ........................... 293
6.3.5.5 Crop unloading-auger control cylinder (35) ........................293
6.3.5.6 Main crop elevator adapter (36) ............................... 294
6.3.5.7 MCS belt tensioner (if installed) (37) ........................... 294
6.3.5.8 Threshing-mechanism belt tensioner (38) ........................ 295
6.3.5.9 Hydrostatic-pump belt tensioner (39) ...........................295
6.3.5.10 Cab access ladder (40) .................................... 296
6.3.5.11 Tires (41) ...............................................296
6.3.5.12 Main crop elevator supports (42) ..............................297
6.3.5.13 Rear wheel 4WD tie rod (if fitted) (43) ..........................298
6.3.5.14 Engine (44) ............................................. 298
6.3.5.15 Engine air filter (45) ....................................... 299
6.3.5.16 Park brake (46) .......................................... 300
6.3.6 Interval - 250 hours ...............................................301
6.3.6.1 Gearbox (61) ............................................. 301
6.3.6.2 Reduction gearbox (62) ..................................... 301
6.3.6.3 Main clutch (63) ...........................................302
6.3.6.4 Unloading auger support (64) ................................. 302
6.3.6.5 Straw chopper driven-belt tensioner (65) .........................303
6.3.6.6 Straw chopper drive-belt tensioner (66) ..........................303
6.3.6.7 Straw chopper idler shaft (67) .................................304
6.3.6.8 Tank unloading-auger clutch (68) ...............................304
6.3.6.9 Aspirator drive-belt tensioner (69) ..............................305
6.3.6.10 Rotary-screen belt tensioner (70) .............................305
6.3.6.11 Windshield wash fluid reservoir (71) ........................... 306
6.3.6.12 Engine oil and filters (72) ................................... 306
6.3.6.13 Tailing-auger left support (73) ............................... 309
6.3.6.14 Unloading-auger top angle gear (74) ........................... 309
6.3.7 Interval - 500 hours ...............................................310
6.3.7.1 Hydraulic systems oil (81) ................................... 310
6.3.7.2 Hydraulic and hydrostatic systems return filter (82) ................. 311
Table of contents
Combines
M300-M310_EN_327305015
Find manuals at https://best-manuals.com
To Next Page
Loading...
