To Next PageTo Next PageHow to fix Lavor Pressure Washer that does not start?
If your Lavor Pressure Washer doesn't start when the main switch is turned on, it might be due to the plug not being properly connected (carefully check the plug and the electric cable) or the connection panel fuses being burnt out (check and replace them).
What to do if Lavor HLR 2021 LP boiler does not start?
If the boiler does not start when turning on the burner switch of your Lavor Pressure Washer, possible causes include: no fuel (check the level in the tank and ensure the rigid suction pipe is clean), a clogged fuel filter (replace the line filter), a blocked or burnt-out fuel pump (replace it), a damaged thermostat (replace it), insufficient or lacking ignition spark (contact an authorised service centre), incorrect space among the electrodes (check the positioning), or a burnt-out fuse (replace it).
What to do if Lavor HLR 2021 LP Pressure Washer has pressure leakage?
Pressure leakage in your Lavor Pressure Washer can be due to several reasons: a worn-out nozzle (in which case, replace it), broken or worn suction and/or delivery valves (check and replace if necessary), foreign matter in the valves (check and clean them), a worn-out setting valve area (check and replace), or worn-out seals (replace them).
Why is my Lavor HLR 2021 LP so noisy?
Noisiness in your Lavor Pressure Washer can be caused by several factors. These include air suction (check the suction pipes), broken or worn suction and/or delivery valve springs (replace the valve springs), foreign matter in the suction and delivery valves (check and clean them), worn-out bearings (replace the bearings), or extreme liquid temperature (reduce the liquid temperature).
Why does my Lavor HLR 2021 LP have irregular pressure fluctuations?
Irregular pressure fluctuations in your Lavor Pressure Washer could be due to worn-out suction and/or delivery valves (check and replace them), foreign matter in the valves (check, clean, and replace them), air suction (check the suction pipe), or worn-out seals (check and replace the seals).
What to do if pressure decreases and increases when the lance is turned on Lavor HLR 2021 LP Pressure Washer?
If the pressure values decrease and increase when the lance is turned on for your Lavor Pressure Washer, it could be due to a clogged or deformed nozzle (clean or replace it) or the boiler coil or lance being clogged with limestone (descaling is required).
Why is there too much smoke from the Lavor Pressure Washer chimney?
If there is too much smoke coming from the chimney of your Lavor Pressure Washer, it could be due to incorrect combustion or impurities/water in the fuel. You should clean the fuel filter, clean the boiler, empty and carefully clean the tank, and clean the fuel filter again.
Why Lavor Pressure Washer has too much vibration at the delivery?
Excessive vibrations at the delivery of your Lavor Pressure Washer can occur if the pressure tank is run down (check the pressure in the tank) or if the valves are worn out or dirty (check and replace them if necessary).
Why Lavor Pressure Washer has insufficient detergent suction?
If your Lavor Pressure Washer isn't suctioning enough detergent, it could be due to an empty detergent tank (fill it), an incrusted injector (clean it), or a clogged coil, tube, or lance (clean or descale).
How to fix water in the oil of Lavor HLR 2021 LP Pressure Washer?
If water is present in the oil of your Lavor Pressure Washer, it could be due to a worn-out O-ring casing (check and/or replace the O-ring), high moisture in the air (replace the oil with double frequency), or completely worn-out seals (replace the seals).
General| Brand | Lavor |
|---|---|
| Model | HLR 2021 LP |
| Category | Pressure Washer |
| Language | English |
Essential warnings and cautions for safe operation of the high-pressure cleaner.
Critical safety advice and warnings to ensure user safety during operation.
Requirements and safety measures for connecting the appliance to the electrical supply.
Step-by-step guide for installing the machine and performing the initial start-up.
A systematic guide to diagnose and resolve common operational problems.
