To Next Page

LV5600 / LV7600

WAVEFORM MONITOR / RASTERIZER

LV5600-SER01 SDI INPUT

LV5600-SER02 SDI INPUT / EYE

LV5600-SER03 / LV7600-SER03 DIGI / ANA AUDIO

LV5600-SER05 / LV7600-SER05 10G IP INPUT

LV5600-SER23 / LV7600-SER23 HDR

LV5600-SER24 / LV7600-SER24 TSG

LV5600-SER25 / LV7600-SER25 FOCUS ASSIST

LV5600-SER26 / LV7600-SER26 LAYOUT

LV5600-SER27 / LV7600-SER27 TALLY

LV5600-SER28 / LV7600-SER28 4K

LV5600-SER29 / LV7600-SER29 12G-SDI

Instruction Manual

Thank you for purchasing.

Please carefully read this instruction manual and the included "GENERAL SAFETY SUMMARY".

Please use the product safely.

Default Chapter2
- Table of Contents2
General Safety Summary15
1 Introduction19
- Scope of Warranty19
- Operating Precautions19
- About Trademarks and Licenses21
- Terminology Used in this Manual21
2 Product Configuration23
- Lineup23
- Hardware Options23
- Software Options24
- Items Sold Separately24
3 Specifications25
- General25
- Features26
- Specifications30
4 Panel Description75
- Front Panel75
- Rear Panel79
5 Before You Begin Measuring82
- Attaching the Cover Inlet Stopper82
- Turning the Instrument on and off83
- Connecting USB Devices83
- Installing the SFP+ Transceiver Module (SER05)84
- Signal I/O85
- Operation Basics95
- Measurement Screen Description100
6 Basic Operation102
- Setting the Input Signals102
- Setting the Signals to Measure106
- Selecting the Measurement Mode127
- Operation Key Actions134
- Customized Layout (SER26)136
- Enhanced Layout (SER26)152
  - Enhanced Layout Procedure153
  - Enhanced Layout Screen Description157
7 System Settings163
- Configuring the I/O Connectors163
- Configuring the Instrument188
- Displaying System Information213
- Installing Software Options214
- Adjusting the Backlight (LV5600)215
- Turning off the LCD Panel (LV5600)215
- Initialization216
8 Capture Feature218
- Screen Capture219
- Frame Capture224
9 Preset Feature229
- Registering Presets229
- Loading Presets231
- Deleting Presets232
- Copying All Presets from the Instrument to a USB Memory Device233
- Copying All Presets from a USB Memory Device to the Instrument234
10 Video Signal Waveform Display235
- Operation Key Description235
- Setting the Waveform Display Position236
- Configuring the Display Settings237
- Configuring the Gain and Filter Settings245
- Configuring the Sweep Settings251
- Configuring the Cursor Settings258
- Configuring the Line Selection Settings262
  - Turning Line Selection on and off262
  - Setting the Line Selection Range263
- Configuring the Color System Settings264
- Displaying the External Sync Signal Waveform268
11 Vector Display270
- Operation Key Description271
- Setting the Display and Waveform Intensity271
- Setting the Scale274
- Setting the Gain277
- Configuring the Marker Settings279
  - Displaying the Vector Marker279
  - Configuring the Variable Marker280
- Configuring the Line Selection Settings281
  - Turning Line Selection on and off281
  - Setting the Line Selection Range282
- Configuring the Color System Settings283
- 5-Bar Display286
  - Selecting the Scale Unit287
  - Selecting the Display Order289
- Histogram Display290
  - Selecting the Display Format290
  - Selecting the Measurement Signal292
12 Cie Chromaticity Diagram Display293
- Setting the Scale293
- Setting the Chromaticity Diagram Mode298
- Displaying Cursors300
- Configuring the Line Selection Settings300
13 Picture Screen301
- Selecting the Display Mode302
- Adjusting the Picture303
- Configuring the Display Settings305
- Configuring the Marker Settings308
- Setting the Superimpose Feature314
- Configuring CINELITE Settings323
- Configuring CINEZONE Settings335
- Focus Assist Display (SER25)339
- Configuring the Line Selection Settings341
14 Hdr Display (Ser23)343
- Video Signal Waveform Display345
- Vector Display354
  - Histogram Display354
- Picture Screen355
- MAXFALL and MAXCLL Displays359
15 Audio Display361
- Setting the Signals to Measure362
- Selecting the Display Mode (SER03)366
- Configuring Error Detection Settings369
- Adjusting the Volume370
- Meter Display371
- Lissajous Display (SER03)374
- Surround Display (SER03)377
- Status Display (SER03)380
- Loudness Display (SER03)384
16 Status Display396
- Status Screen Description396
- Configuring Error Detection Settings401
- Clearing Error Counts410
- Configuring Event Log Settings410
- Configuring Phase Difference Measurement Settings424
  - Phase Difference Measurement Screen Description425
- Setting the Lip Sync Measurement (SER03)429
- Configuring the IP Screen (SER05)434
- Displaying a List of Ancillary Data446
- 16.10 Detecting Ancillary Packets449
17 Eye Pattern Display (Ser02)466
- Eye Pattern Display Description468
- Jitter Display Description469
- Setting the Waveform Display Position470
- Switching between Eye Pattern and Jitter470
- Setting the Intensity471
  - Adjusting the Waveform Intensity471
  - Adjusting the Scale Intensity471
- Selecting the Display Colors472
  - Selecting the Waveform Color472
  - Selecting the Scale Color472
- Configuring Error Detection Settings473
- Configuring Eye Pattern Display Settings481
18 Remote Control494
- Bit Mode495
- Binary Mode498
- Command Mode500
- Tally Mode (SER27)502
19 Rs-422/485 (Ser27)504
- Transmission Commands506
- Response Messages513
20 Network Control514
- SNTP Client Function514
  - How to Use514
  - Time Adjustment Value515
- Telnet516
- Ftp536
- Http538
- Snmp544
21 Menu Tree587
- INPUT Menu587
- SYS Menu588
- CAP Menu592
- MEM Menu594
- RECALL Menu595
- WFM Menu596
- VECT Menu599
- PIC Menu604
- AUDIO Menu609
- 21.10 STATUS Menu613
- EYE Menu (SER02)619
- 21.12 MULTI Menu621

Brand	Leader
Model	LV7600-SER26
Category	Monitor
Language	English

Leader LV7600-SER26 User Manual

Table of Contents

Questions and Answers:

Leader LV7600-SER26 Specifications

Related product manuals