Leggett & Platt Falcon 2.0+

Questions and Answers

M
millerginaJul 29, 2025
What to do if Leggett & Platt Falcon 2.0+ Indoor Furnishing remote is not activating the base?
- R
  Randall LucasJul 29, 2025
  If your Leggett & Platt Indoor Furnishing remote control lights up but doesn't activate the base, try these steps: First, test the outlet by plugging in another working appliance to ensure the outlet is functional. If the outlet is working, wait 30 minutes before attempting to operate the base again. To prevent future issues, avoid exceeding the duty cycle once the base returns to normal operation.
E
Eric CunninghamAug 3, 2025
What to do if no features of Leggett & Platt Falcon 2.0+ base will activate?
- J
  James SmithAug 4, 2025
  If none of the features on your Leggett & Platt Indoor Furnishing base are working, try the following: First, check the electrical service breaker box to verify it's not tripped. Then, test the outlet by plugging in another working appliance. You can also try to reset the electronic components. If these steps don't resolve the issue, refer to the Remote Control Programming section of this manual for programming procedures.
Z
zhuangAug 10, 2025
How to fix a Leggett & Platt Falcon 2.0+ Indoor Furnishing remote control that will not illuminate?
- E
  Elizabeth TorresAug 10, 2025
  If your Leggett & Platt Indoor Furnishing remote control will not illuminate, replace the batteries in the remote.
B
Bill MccormickAug 15, 2025
Why won't the head or foot section of my Leggett & Platt Falcon 2.0+ return to the flat position?
- H
  Henry MurrayAug 15, 2025
  If the head or foot section of your Leggett & Platt Indoor Furnishing elevates but does not return to the horizontal position, first check for any obstructions and remove them. Also, ensure there's a 1.5” (38.1mm) to 2” (50.8mm) distance between the headboard brackets and the mattress; adjust if needed.
J
Jessica DayAug 21, 2025
How to reduce massage motor noise in Leggett & Platt Falcon 2.0+ Indoor Furnishing?
- W
  Wendy AdamsAug 21, 2025
  To reduce excessive massage motor noise in your Leggett & Platt Indoor Furnishing, consider these steps: First, place rubber caster cups under each leg or caster of the base. Make sure that the base isn't touching a nightstand or anything else that might cause vibration or noise. Check that motors are not causing bed frame (or bed frame components) to vibrate. Finally, realign the lift/lower mechanisms with the base support platform.

Summary

Advisory and Important Information

User and Environmental Warnings

Details safety warnings for children, pets, pacemakers, hospital use, and environmental factors like explosive gases.

Installation

Initial Setup and Inventory

Check package contents and prepare the base by removing packaging and attaching legs.

Base Assembly Steps

Guides on attaching legs, positioning the base, and removing protective materials.

Final Installation and Testing

Steps for connecting power, testing functions, and returning the base to level.

Completing Mattress Setup

Details on placing mattress retainers and the mattress on the adjustable base.

Remote Control Function

Head Section Control

Details the 'Head Up', 'Head Down', and 'Head/Foot Up' buttons for adjusting the head section.

Foot Section Control

Base Leveling and Lighting

Remote Control Programming

One Remote Control Scenarios

Two Remote Control Scenarios

Power Down Operation

Preparing the Power Down Device

Executing Power Down Lowering

Troubleshooting

Remote Not Activating Base

Solutions for when the remote illuminates but the base does not activate.

No Base Features Activate

Troubleshooting steps when none of the base features respond.

Remote Control Not Illuminating

Base Not Returning to Flat

Solutions for when head or foot sections elevate but won't return to horizontal.

Excessive Massage Noise

1 Year, 3 Year, and 25 Year Limited Warranty

First Year Warranty Coverage

Years 2-3 Limited Warranty

Years 4-25 Limited Warranty

Leggett & Platt Falcon 2.0+ Specifications

General

Type	Adjustable Bed Base
Weight Capacity	850 lbs
Adjustable Positions	Head and Foot
Wall Hugging	Yes
Mattress Compatibility	Foam, Hybrid, Innerspring, Latex
Remote Control	Wireless
Warranty	1-3-25 warranty