Lehmannaudio Rhinelander

Questions and Answers

M
Mitchell WaltersAug 16, 2025
How to fix Lehmannaudio Rhinelander if LED indicator is not on?
- P
  Peter Miller DDSAug 16, 2025
  If the LED indicator on your Lehmannaudio Amplifier is not lit, first ensure the power supply or cord is properly connected to a power outlet. If it's connected, check that the device is turned on using the mains switch on the rear. If the problem persists, the fuse may be defective, so check the fuse. If the wire is broken, replace the fuse. If the fuse fails repeatedly, the device may be faulty and should be inspected by your dealer.
S
Samantha MartinAug 19, 2025
What to do if there is no headphone signal from Lehmannaudio Rhinelander?
- E
  Erica JonesSep 12, 2025
  If you're not getting any headphone signal from your Lehmannaudio Amplifier, first ensure that the signal source is actually sending a signal to the device. Next, check the volume control and make sure it isn't set to the minimum. Finally, verify that your headphone is securely plugged into the headphone socket.
H
hunttraciAug 22, 2025
Why is the Lehmannaudio Rhinelander Amplifier signal too soft?
- R
  Rachel PaceAug 22, 2025
  If the signal from your Lehmannaudio Amplifier is too soft, try these steps: 1. Increase the volume control. 2. If possible, select a stronger signal source or raise the level of the current source. 3. Increase the gain factor, referring to the user manual and adjusting the DIP switch accordingly. 4. For USB versions, check that all PC internal controls are set to maximum.
J
Jacob BrownAug 25, 2025
What causes distorted signal on Lehmannaudio Rhinelander?
- J
  Jessica JonesAug 26, 2025
  If the signal from your Lehmannaudio Amplifier is distorted, first turn down the volume of the connected signal source. If that doesn't solve the problem, try using another headphone set to rule out a defective headphone. You can also try playing a different track or using another sound carrier to ensure the signal itself isn't distorted. Also, lower the gain factor and set the DIP switches accordingly, referring to the user manual.
R
robert02Aug 28, 2025
Why is there no signal at the line output on my Lehmannaudio Amplifier?
- C
  Christine AguilarAug 28, 2025
  If there's no signal at the line output of your Lehmannaudio Amplifier, first, ensure that a headphone is not plugged into the left headphone output; if it is, remove it or plug it into the right socket. Also, verify that the device is receiving a signal from the source. Finally, check that the volume control is not set to the minimum level.
J
Joshua HarrisAug 31, 2025
How to troubleshoot Lehmannaudio Rhinelander signal on only one channel?
- M
  mackenziehughesAug 31, 2025
  If you're only getting a signal on one channel from your Lehmannaudio Amplifier, first check the settings of both DIP switches and correct them according to the user manual if they are set unequally. Also, inspect the connection cable between the source and the headphone amplifier for any loose contacts, incomplete insertion, or defects, and replace it if necessary.
E
Edward StephensSep 3, 2025
Why does Lehmannaudio Amplifier headphone signal not respond to volume control?
- H
  Hannah LeeSep 3, 2025
  If the headphone signal on your Lehmannaudio Amplifier isn't responding to the volume control, it's likely that the cable from the signal source is plugged into the output sockets instead of the input sockets. Make sure to plug the cable into the correct input sockets.
J
James SinghSep 6, 2025
What to do if left and right channels are messed up on Lehmannaudio Rhinelander?
- P
  Phillip WallaceSep 6, 2025
  If the left and right channels are mixed up on your Lehmannaudio Amplifier, check all connection cables and reverse the channels if necessary. Also, make sure you're wearing the headphone correctly, in line with its labeling.
J
jonesjennySep 9, 2025
Why can I hear radio interference in the background on Lehmannaudio Rhinelander Amplifier?
- P
  Pamela BrooksSep 9, 2025
  If you're hearing radio interference in the background with your Lehmannaudio Amplifier, the issue might be the signal cables. Try using suitable signal cables. Additionally, check the screen on the signal cable for defects and replace the cable if needed.
D
Dr. Ashley Miranda PhDSep 12, 2025
What causes audible hum in Lehmannaudio Amplifier?
- T
  Todd VegaSep 12, 2025
  If you're experiencing an audible hum with your Lehmannaudio Amplifier, it could be due to a ground loop caused by several connected devices. To resolve this, establish a correct earth connection. If necessary, contact an electrician.

Lehmannaudio Rhinelander Specifications

General

Type	Headphone Amplifier
Gain	10 dB
Power Consumption	10 W
Inputs	1 x RCA, 1 x 3.5mm
Signal-to-Noise Ratio	> 100 dB
Outputs	1 x 6.3mm, 1 x RCA
Power Supply	External Power Supply