Contents
viii
SHB9300CRV EN 2.0
7.6.74.4 Time window for the synchronization via terminal 7-224........................
7.6.74.5 Correction value phase controller 7-224....................................
7.6.74.6 Fault indications 7-225.................................................
7.6.74.7 Configuration examples 7-225...........................................
7.6.74.8 Scaling 7-226.......................................................
7.6.75 Edge evaluation (TRANS) 7-227....................................................
7.6.75.1 Evaluate positive edge 7-228............................................
7.6.75.2 Evalute negative edge 7-228............................................
7.6.75.3 Evaluate positive or negative edge 7-229...................................
7.6.76 Virtual master (VMAS) 7-230......................................................
7.6.76.1 Generation of a virtual master value 7-231..................................
7.6.76.2 Digital frequency input 7-231............................................
7.6.76.3 Changeover to alternative master value 7-231................................
7.6.76.4 Inching 7-232.......................................................
7.6.76.5 Ramp function integrator 7-232..........................................
7.6.77 Positioning control (VTPOSC) 7-233.................................................
7.6.78 Welding bar control (WELD) 7-235..................................................
7.6.78.1 Basics of welding bar control 7-236.......................................
7.6.78.2 Cam data 7-237......................................................
7.6.79 Stretching, compression, offset in Y direction (YSET) 7-241................................
7.6.79.1 Stretching/compression 7-241...........................................
7.6.79.2 Offset 7-242........................................................
7.6.79.3 Direction reversal 7-242................................................
7.7 Monitoring 7-243......................................................................
7.7.1 Reactions 7-243...............................................................
7.7.2 Setting of reactions 7-244........................................................
7.7.3 Monitoring functions 7-245.......................................................
7.7.3.1 Undervoltage LU 7-248.................................................
7.7.3.2 Overvoltage OU 7-249.................................................
7.7.3.3 Heatsink monitoring OH (fixed) 7-251......................................
7.7.3.4 Heatsink monitoring OH4 (adjustable) 7-252.................................
7.7.3.5 Motor temperature monitoring OH8 7-253...................................
7.7.3.6 Motor temperature monitoring OH7 (adjustable) 7-254..........................
7.7.3.7 Motor temperature monitoring OH3 (fixed) 7-255.............................
7.7.3.8 External fault EEr 7-256................................................
7.7.3.9 Earth fault monitoring OC2 7-257.........................................
7.7.3.10 Monitoring for short-circuit OC1 7-258.....................................
7.7.3.11 Motor phase failure monitoring LP1 7-259...................................
7.7.3.12 Resolver monitoring for open circuit Sd2 7-260...............................
7.7.3.13 Dig-Set monitoring Sd3 7-261...........................................
7.7.3.14 System fault CCr 7-262................................................
7.7.3.15 Parameter set error PR1, PR2, PR3, PR4 7-263...............................
7.7.3.16 Parameter error PRO 7-264..............................................
7.7.3.17 Communication error CE0 7-265..........................................
7.7.3.18 Contouring error P03 7-266.............................................
7.7.3.19 Phase controller overflow P13 7-267.......................................
7.7.3.20 Power stage identification H07 7-268......................................
7.7.3.21 Fault after automatic adjustment H30 7-269.................................
7.7.3.22 Fault in the resolver driver H06 7-270......................................
7.7.3.23 System speed monitoring NMax 7-271.....................................
7.7.4 Fault indication via digital output 7-272..............................................
7.8 Parameter setting 7-273.................................................................
7.8.1 Parameter setting in GDC 7-278....................................................
7.8.1.1 Change parameters 7-278..............................................
7.8.1.2 Parameter set transfer 7-279............................................
7.8.2 Parameter change using the keypad 7-280............................................
To Next Page
Loading...