Lenze i55AE215F - Page 102

Display code Short designaon Default seng Seng range Address Category
└ P700.08 Load par. set 2 O / ready [0] Selecon list 0x2022:008 general
└ P700.09 Load par. set 3 O / ready [0] Selecon list 0x2022:009 general
└ P700.10 Load par. set 4 O / ready [0] Selecon list 0x2022:010 general
└ P700.11 Save par. set 1 O / ready [0] Selecon list 0x2022:011 general
└ P700.12 Save par. set 2 O / ready [0] Selecon list 0x2022:012 general
└ P700.13 Save par. set 3 O / ready [0] Selecon list 0x2022:013 general
└ P700.14 Save par. set 4 O / ready [0] Selecon list 0x2022:014 general
└ P700.15 Delete logbook O / ready [0] Selecon list 0x2022:015 general
P701.00 KP setp. incr. 1 1 ... 100 0x2862 general
P702.00 Scal.speed fact. 0.00 0.00 ... 650.00 0x4002 general
P703.00 KP status displ. 0x00000000 0x00000000 ... 0xFFFFFF00 0x2864 general
P704.xx DC braking
└ P704.01 Current 0.0 % 0.0 ... 200.0 % 0x2B84:001 general
└ P704.02 Hold me autom. 0.0 s 0.0 ... 1000.0 s 0x2B84:002 general
└ P704.03 Threshold autom. 0.0 Hz 0.0 ... 599.0 Hz 0x2B84:003 general
└ P704.04 Demagnet. me 100 % 0 ... 150 % 0x2B84:004 general
└ P704.05 Def. demag. me x ms - (Read only) 0x2B84:005 general
└ P704.06 DCbrk/inv.disab 0 0 ... 1 0x2B84:006 general
P705.00 KP language English [1] Selecon list 0x2863 general
P706.xx Brake management
└ P706.01 Operang mode Rfg stop (RFGS) [1] Selecon list 0x2541:001 general
└ P706.02 Acve threshold x V - (Read only) 0x2541:002 general
└ P706.03 Red. threshold 0 V 0 ... 100 V 0x2541:003 general
└ P706.04 Add.frequency 0.0 Hz 0.0 ... 10.0 Hz 0x2541:004 general
└ P706.05 Del.overr.me 2.0 s 0.0 ... 60.0 s 0x2541:005 general
└ P706.06 Brk. res. behav O:disabl+error [0] Selecon list 0x2541:006 general
P707.xx Brake resistor
└ P707.02 Resistance value 180.0 Ω * 0.0 ... 500.0 Ω 0x2550:002 general
└ P707.03 Rated power 50 W * 0 ... 800000 W 0x2550:003 general
└ P707.04 Maximum heat 8.0 kWs * 0.0 ... 100000.0 kWs 0x2550:004 general
└ P707.07 Thermal load x.x % - (Read only) 0x2550:007 general
└ P707.08 Warning thresh. 90.0 % 50.0 ... 150.0 % 0x2550:008 general
└ P707.09 Error thresh. 100.0 % 50.0 ... 150.0 % 0x2550:009 general
└ P707.10 Warning resp. Warning [1] Selecon list 0x2550:010 general
└ P707.11 Error response Fault [3] Selecon list 0x2550:011 general
P708.xx Keypad setup
└ P708.01 CTRL&F/R keys CTRL&F/R Enable [1] Selecon list 0x2602:001 general
└ P708.02 Select rot.dir. Forward [0] Selecon list 0x2602:002 general
└ P708.03 Keypad Full Ctrl O [0] Selecon list 0x2602:003 general
P710.xx Load loss detect
└ P710.01 Threshold 0.0 % 0.0 ... 200.0 % 0x4006:001 general
└ P710.02 Deceleraon 0.0 s 0.0 ... 300.0 s 0x4006:002 general
P711.xx Posion counter
└ P711.01 Signal source Disbled [0] Selecon list 0x2C49:001 general
└ P711.02 Reset mode Rising edge [0] Selecon list 0x2C49:002 general
└ P711.03 Actual posion - - (Read only) 0x2C49:003 general
P712.xx Brake control
└ P712.01 Brake mode O [2] Selecon list 0x2820:001 general
└ P712.02 Closing me 100 ms 0 ... 10000 ms 0x2820:002 general
└ P712.03 Opening me 100 ms 0 ... 10000 ms 0x2820:003 general
└ P712.07 Closing thresh. 0.2 Hz 0.0 ... 599.0 Hz 0x2820:007 general
└ P712.08 Holding load 0.0 % -500.0 ... 500.0 % 0x2820:008 general
└ P712.12 ClosingThr delay 0 ms 0 ... 10000 ms 0x2820:012 general
└ P712.13 HoldLoad rampm 0 ms 0 ... 100 ms 0x2820:013 general
* Default seng depending on the size. Firmware version 05.00.00.00
Commissioning
Keypad parameter list
102