wiping 82, 130, 179
printer hard disk
encryption 83, 130, 179
printer hard disk memory
erasing 82, 130, 179
printer information
where to find 9
printer IP address
finding 91, 139
printer is printing blank pages 329
printer messages
[x]‑page jam, clear manual feeder.
[250] 277
[x]‑page jam, lift front cover to
remove cartridge. [200–
201] 269
[x]‑page jam, open tray [x].
[24x] 276
[x]‑page jam, open upper and
lower rear door. [231–234] 272
[x]‑page jam, open upper rear
door. [202] 271
[x]‑page jam, remove paper, open
expander rear door. Leave paper
in bin. [41y.xx] 283
[x]‑page jam, remove paper, open
finisher rear door. Leave paper in
bin. [451] 282
[x]‑page jam, remove paper, open
mailbox rear door. Leave paper
in bin. [43y.xx] 285
[x]‑page jam, remove paper, open
stapler door. Leave paper in bin.
[455–457] 278
[x]‑page jam, remove standard bin
jam. [203] 275
[x]‑page jam, remove tray 1 to
clear duplex. [235–239] 275
Cartridge low [88.xy] 287
Cartridge nearly low [88.xy] 287
Cartridge very low, [x] estimated
pages remain [88.xy] 287
Change [paper source] to [custom
string] load [orientation] 287
Change [paper source] to [custom
type name] load
[orientation] 288
Change [paper source] to [paper
size] load [orientation] 288
Change [paper source] to [paper
type] [paper size] load
[orientation] 288
Check tray [x] connection 288
Close door or insert cartridge 289
Close rear door 289
Complex page, some data may not
have printed [39] 289
Configuration change, some held
jobs were not restored [57] 289
Defective flash detected [51] 289
Disk must be formatted for use in
this device 289
Disk near full. Securely clearing
disk space. 290
Empty the hole punch box 290
Error reading USB drive. Remove
USB. 290
Error reading USB hub. Remove
hub. 290
Imaging unit low [84.xy] 290
Imaging unit nearly low
[84.xy] 290
Imaging unit very low, [x]
estimated pages remain
[84.xy] 290
Incompatible output bin [x]
[59] 291
Incompatible tray [x] [59] 291
Incorrect paper size, open [paper
source] [34] 291
Insert hole punch box 291
Insert staple cartridge 291
Insert Tray [x] 292
Install bin [x] 292
Install Tray [x] 292
Insufficient memory for Flash
Memory Defragment operation
[37] 292
Insufficient memory to collate job
[37] 293
Insufficient memory to support
Resource Save feature [35] 293
Insufficient memory, some Held
Jobs were deleted [37] 292
Insufficient memory, some held
jobs will not be restored
[37] 293
Load [paper source] with [custom
string] [paper orientation] 293
Load [paper source] with [custom
type name] [paper
orientation] 294
Load [paper source] with [paper
size] [paper orientation] 294
Load [paper source] with [paper
type] [paper size] [paper
orientation] 294
Load manual feeder with [custom
string] [paper orientation] 294
Load manual feeder with [custom
type name] [paper
orientation] 295
Load manual feeder with [paper
size] [paper orientation] 295
Load manual feeder with [paper
type] [paper size] [paper
orientation] 295
Load staples 293
Maintenance kit low [80.xy] 295
Maintenance kit nearly low
[80.xy] 295
Maintenance kit very low, [x]
estimated pages remain
[80.xy] 296
Memory full [38] 296
Network [x] software error
[54] 296
Non‑Lexmark [supply type], see
User’s Guide [33.xy] 296
Not enough free space in flash
memory for resources [52] 297
Paper changes needed 297
Parallel port [x] disabled [56] 297
PPDS font error [50] 297
Reattach bin [x] 298
Reattach bins [x] – [y] 298
Reinstall missing or unresponsive
cartridge [31.xy] 299
Reinstall missing or unresponsive
imaging unit [31.xy] 299
Remove defective disk [61] 299
Remove packaging material, [area
name] 299
Remove paper from [linked set bin
name] 300
Remove paper from all bins 299
Remove paper from bin [x] 300
Remove paper from standard
output bin 300
Replace cartridge, 0 estimated
pages remain [88.xy] 300
Replace cartridge, printer region
mismatch [42.xy] 300
Replace imaging unit, 0 estimated
pages remain [84.xy] 301
Index 364
To Next Page
Loading...
Need help?
General
Weight and Dimensions
