LG 22LK3 Series - Page 217

84
APPENDIX
APPENDIX
12. Remote control lock / Key Lock Mode
(Command: k m)
► To lock the remote control and the front panel controls
on the set.
Acknowledgement
Data 00 : Lock off 01 : Lock on
[m][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 00 : OSD off 01 : OSD on
[l][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission
Data Red : 00 to Green : 64
*
Refer to ‘Real data mapping 1’. See page 85.
[k][j][ ][Set ID][ ][Data][Cr]
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
10. Sharpness (Command: k k)
Data Min : 00 to Max : 64
*
Refer to ‘Real data mapping 1’. See page 85.
[k][k][ ][Set ID][ ][Data][Cr]
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
15. Treble (Command: k r)
► To adjust Treble.
Transmission
Data Min : 00 to Max : 64
*
Refer to ‘Real data mapping 1’. See page 85
[k][r][ ][Set ID][ ][Data][Cr]
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
14. Colour Temperature (Command: k u)
► To adjust colour temperature.
You can also adjust Colour Temperature in the
PICTURE menu.
Transmission
Data 00: Medium 01: Cool 02: Warm
[k][u][ ][Set ID][ ][Data][Cr]
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
16. Bass (Command: k s)
► To adjust bass
Transmission
Data Min: 00 to Max: 64
*
Refer to ‘Real data mapping 1’. See page 85.
[k][s][ ][Set ID][ ][Data][Cr]
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
13. Balance (Command: k t)
► To adjust balance.
You can also adjust
balance.
in the AUDIO menu.
Transmission
Data Min : 00 to Max : 64
*
Refer to ‘Real data mapping 1’. See page 85.
[k][t][ ][Set ID][ ][Data][Cr]
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
[k][m][ ][Set ID][ ][Data][Cr]
Transmission
17. Abnormal State (Command: k z)
► Torecognizeanabnormalstate.
Transmission
Data FF: Read
Data 00: Normal (Power on and signal exist)
Data 01: No signal (Power on)
Data 02: Turn the TV off by remote control
Data 03: Turn the TV off by sleep time function
Data 04: Turn the TV off by RS-232C function
Data 05: 5V down
Data 06: AC down
Data 07: Turn the TV off by Fan Alarm function (option)
Data 08: Turn the TV off by Off time function
Data 09: Turn the TV off by Auto off function
Data a: Turn the TV off by AV board detection.
* This function is “read only”.
[k][z][ ][Set ID][ ][Data][Cr]
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
* When main power is on/off, remote control lock is
released.
* In the standby mode, if key lock is on, TV will not
turn on by power on key of IR & Local Key.