EasyManuals Logo

LG F1403TDS User Manual

LG F1403TDS
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
W
ater supply is not adequate in area
W
ater supply taps are not completely open.
Water inlet hose(s) are kinked.
The filter of the inlet hose(s) are clogged.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
• Load is too small
• Load is out of balance.
The appliance has an unbalance detection
and correction system. If individual heav
y
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Is the door opened or not
completely closed?
Water overfills due to the faulty water
valve.
Water level sensor has malfunctioned.
• Over load in motor.
Water leaks
• The washer experienced a power failure.
Check another tap in the house.
Fully open tap.
Straighten hose(s)
.
Check the filter of the inlet hose(s)
.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to
Cleaning the drain pump filter
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
Close the door completely
.
If “ ”is not released, call for service
.
Unplug the power plug and call for service.
Close the water tap.
Unplug the power plug.
Call for service
.
Call for service
.
Restart the cycle.
4
1
2
3
7
5
3. Die 4 Schrauben lösen und die
Gummipfropfen etwas drehen, um sie
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
Die Transportsicherungsschrauben müssen vor
jedem Transport des Geräts wieder angebracht
werden.
4. Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
1 2
3 4
Schraubenschlüssel
6
60 - 100 cm
@
N
Green and Yellow(Earth)
Brown(Live)
Blue(Neutral)
Fuse
Cord
grip
E
L
N
Adjustable feet
Adjustable feet
CAUTION
The appliance is not inte nded for use by young children or infi rm persons withou t supervision.
Young Children should be super vised to ensure that they do not play with ap pliance.
Disposal
Whe n this crossed-out wheele d bin symbol is attached to a pr oduct it means the produc t is
covered by Europe an Directive 2002/ 96/EC.
All e lectrical and electron ic products should be dispo sed of separately from munic ipal
waste stream v ia designated collection f acilities appointed by the gover nment or the local
authorities .
The c orrect disposal of your old ap pliance will help prevent poten tial adverse consequences
for the environm ent and human health.
For mo re detailed information a bout disposal of your old appli ance, please contact your ci ty
offi ce, waste disposa l service or the shop where you p urchased the product .
BS Plug Safety Details (For U.K. User)
This appliance must be earthed As the colours of the wires in the mains lead of
this apparatus may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows: The green and yellow wire must be
connected to the terminal in the plug marked E or by the earth symbol or
coloured green or green and yellow. The wire coloured blue must be connected to
the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal
marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fi t a 13 amp BS 1362 fuse.
Owners Manual
F1403TDS(1~9)
F1203TDS(1~9)
Safe ty instru ctions fo r use
Read all instruc tions and explanations of the ins tallation before use. Foll ow the instructions caref ully. Keep the
operating inst ructions handy for later use. If th e appliance is sold or passed on then ensur e that the new owner
always receives t hese operating instru ctions. The following war nings must be strictly observed for safet y rea-
sons. They must b e read before installing the a ppliance and putting it int o operation.
Intended us e: This appliance has been designed exclusively for use in dr y-interior households. Use the appliance only
with cold drinking water and o nly for washing textiles with washing detergents des igned for washing machines. Every
other use is improper and may lead to injuri es, whereby the liability of the manufacturer will cea se.
This applia nce may only be used by adults. Do not allow children to touch the co ntrols or to play with the product.
Never modif y the appliance on your own, as this is dangerous.
This applia nce is heavy. Transporting with care.
Remove all pack aging and transport bolts before using the a ppliance. Otherwise serious damage may result.
All inst allation work must be carried out by a qualifi ed fi tter or technician.
Have elect rical connections done by a qualifi ed electrician.
Never place th e appliance on the power cord.
If the app liance is placed on a carpet then place the feet so that air c an circulate underneath the appliance.
Always unplug t he machine and turn off the water supply after use. D isconnect appliance by pulling only the plug
- never disconnect by pulling the powe r cord. Never touch the plug with wet fi ngers or hands.
Do not overlo ad the appliance.
Wash only machine -washable textiles. If you have doubts regarding thi s, then observe the markings on the label.
Never place ele ctrical heaters, candles etc. in the vicinit y of the appliance. They could cause the appliance to igni te or
parts to warp.
Protect th e appliance from wet and damp. Otherwise, there is d anger of electric shock and fi re.
Connec t the appliance to a suitable wall socket for 220 -240V. Never use an extension cord or double adapter.
Empty all p ockets. Hard or sharp objects such as co ins, needles, nails, screws or stones may cause serious damag e.
Unbalanced mass may create he avy vibrations. If heavy vibrations re main also without load, call for an authorized
customer service.
Do not wash or d ry articles that have been cleaned in, washed in, so aked in, or dabbed with combustible or explosive
substances (such as wa x, oil, paint, gasoline, degreasers, dry-clea ning solvents, kerosene, etc.). This may result in
re or explo sion.
Never inser t products coated with mineral oils (e.g. nylon coatin g, plastic belts, etc. ) into the machine. If a stain re-
mover has been used then make sure th at the solvent has been carefully washed out before ins erting the clothes into
the appliance. Oil may remain in the tub af ter a whole cycle resulting in fi re dur ing drying. So, do not load oily clothes.
Do not oper ate the appliance at locations where fl ammable substances are pres ent such as oil, benzene or highly
infl ammable gas. Such materials may cause fi re or explosion. Never use co mbustible detergents.
Only add the pr escribed amount of softener. Excessive amounts may d amage the clothes.
After w ashing, keep the drum door open to protect the doo r seal.
Make sure that a ll water has run off before opening the door. Never open the do or if water still remains. Danger of
scalding.
Animals and child ren may get into the washing machine. So always check the appliance b efore using it.
During washing, t he glass door becomes very hot. Keep childre n away from the appliance when in operation.
Never tr y to repair the machine yourself. Incorrect repairs m ay result in injuries and/or serious defects to the machine.
The produ ct should be serviced and repaired only by the aut horised customer service using original repl acement
parts.
When dispo sing of your old machine, the power cable must be capped and the d oor lock must be made unusable in
order to protect children.
When placing o n a carpeted fl oor, make sure that the opening in t he socket is not blocked.
If the app liance has been under water then contact the custome r service. There is danger of electric shoc k and fi re.
The cover cup of t he fi lter as well as the dispenser drawer may n ot be opened during the operation.
Keep all washing p owder and detergents away from children. Danger of poisoning
Before use please read car efully the safety instructions!
Thank you for b uying an LG fully automat ic washing machine.
Please read t his owner‘s manual ca refully, it provides instr uctions on safe inst allation, use and maint enance.
Keep it handy fo r future reference of thi s machine. Make a note of the mod el and serial numbers of y our washing machine.
Remove Packag ing
Requ ireme nts for instal lation site
Transit bolts
Electrical connecti on
• The appliance is fi tted with transit bolts to prevent internal
damage during transpor t. Be careful, heavy load!
• Packing and all transi t bolts must be removed before using
the washing machine.
• When unpacking the b ase, be sure to remove the additional
packing support in th e middle of the base packing.
Store original packing fo r future move.
Dispose of packing materia l according to local regulations.
Unscrew the 4 bolts
using the spanner
supplied.
Keep the 4 bolts and the spanner for the future use. Re t transit bolts before transporting the appliance.
Level fl o or: Permissible fl oor grad ient under entire washing machine
is 1˚ .
Power socket: Must b e within 100 cm of either side of location of
washing machine. Do not overload the so cket with more than one
appliance.
Additional Cle arance: For wall, fl oor a nd door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or st ore laundry pro-
ducts on top of the washing machine a t any times. They can damage
the fi nish or c ontrols of the machine.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly quali ed person
to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
Repairs to the washing machine must only be carried out by quali ed personnel. Repairs carried out by inexpe-
rienced persons may cause injury or serious malfunctioning. Contact your local service centre.
Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
I f the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
• The drain hos e should not be placed higher than 100 cm above the fl oor.
• Proper secur ing of the drain hose will protect the fl oor from damage due to any water leakage.
• If the drain ho se is too long do not force back into the washing machine. This will cau se unusual noise.
Proper level-adjustment of the wa shing ma-
chine prevents excessive noise and v ibration.
Install the appliance on a s olid and level fl oor
surface, preferably in a co rner of the room.
If the fl oor is uneven, adjust feet as required.
(Do not insert pie ces of wood etc. under the
feet). Make sure that all four feet are s table
and resting on the fl oor. Then check that
the appliance is perfe ctly level. (Use a spirit
level).
Safe ty instuc tions for the i nstallatio n
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted oor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION abou t positioning the appliance
Install the washing machine on a fl at hard fl oor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
Never try to correct any unevenness in the fl oor using pieces of wood, cardboard or similar materials under the washing machine.
If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
The washing machine must not be installed in rooms where the temperature may drop below 0°C.
Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
CAUTION abou t the power cord
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the speci cations of this owners manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or re. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten-
tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
CAUTION abou t location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop-
cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no oor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic lm, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION abou t the fl oor surfac e
The installation surface must be clean, dry and level.
Install washing machine on a fl at hard fl oor.
Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
The washing machine must be perfectly level and fi rmly in position.
It must not “see-saw” across corners under load.
The installation surface must be clean, free from fl oor wax and other lubricant coatings.
Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
Name of product Front loading washing machine
Power supply 220~240 V~, 50 Hz
Size WxDxH mm: 600 x 590 x 850
Weight 63 kg
Max. Watt
2100 W (Wash) / 1100 W (Steam)
Wash capacity 8 kg
Water consumption 52 (6.5 / kg)
Permissible water pressure 1.0-10 bar (100-1000kPa)
Rattling and cl anking noise Extraneous o bjects such as coins or safety pins maybe in drum or p ump.
Thumping sound Heavy wash loads may produce a th umping sound. This is usually normal.
Vibrating noi se Have all transit bolts and p acking been removed?
Water leaks. Check and tighten hose conne ctions. Unclog drain pipe.
Contact plumber if nec essary.
Excessive suds Too much dete rgent or unsuitable detergent.
Washing machine does n ot start Power cord may not be plugged in or conne ction may be loose.
Washing machine won’t s pin Check that the door is fi rmly shut.
Door does not ope n Once started, th e door can not be opened for safety reasons.
Wait one or two minutes before o pening the door to allow the electric
locking mechanism time to relea se.
Troubleshoot ing
Level adjus tment
To prevent internal dama-
ge during transport , the
special 4 bolts are locke d.
If they are not removed, it
may cause heavy vibrati-
on, noise and machine to
malfunction.
Installation of drain hose
Technical Spe cifi cation
i
i
5
Conne cting wate r supply ho se
• Two rubbe r seals are supplied with the water inlet hoses. They are us ed for preventing water leaks.
• M ake sure the connection to taps is tight enough.
• P eriodically check the condition of the hose and r eplace the hose if necessary.
• M ake sure that there is no kink on the hose and that it is not cru shed.
Water supply pressure must be bet ween 1.0-10 bar (100kPa~1000kPa)
Don’t strip or crossthre ad when connecting inlet hose to the valve.
If the water supply pressure i s more than 1000kPa, a decompression
device should be installed.
If after completing co nnection water leaks from the hose, repeat the s ame steps. Use the most conventional
type of tap for water sup ply. In case the faucet is square or too big, remove the spacing ring be fore inserting
the tap into the adaptor.
i
The hose supplied w ith the machine must be used. Old h oses may not be reused
Close the holes with
the caps supplied.
Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.
P/No. :MFL5 9755582
For the U.K. custome r
CUSTOMER SERVI CES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413
LGEUK SERVICE WE B-SITE : http://www.lge.co.uk

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the LG F1403TDS and is the answer not in the manual?

LG F1403TDS Specifications

General IconGeneral
TypeFront Load
Capacity8 kg
Spin Speed1400 rpm
Energy RatingA+++
Energy Efficiency ClassA+++
Spin-Drying ClassB
Water Consumption per Cycle50 L
Noise Level Washing54 dB
Width600 mm
Height850 mm
Water Consumption50 L
Weight70 kg
ColorWhite
Inverter MotorYes
Smart FunctionNo

Related product manuals