EasyManua.ls Logo

LG F4V9BWP2E - User Manual

LG F4V9BWP2E
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved
OWNER'S MANUAL
WASHING
MACHINE
Before beginning installation, read these instructions carefully.
This will simplify installation and ensure that the product is installed correctly
and safely. Leave these instructions near the product after installation for future
reference.
EN ENGLISH
F1612SBS V2-B12X3W F4V9BWP2E F4V9BWP2W
MFL71485441
Rev.01_052720

Table of Contents

Questions and Answers

  • S
    Shelley LarsonAug 10, 2025
    Why does my LG F4V9BWP2E show a UE UNBALANCE ERROR?
    • K
      Kristopher SmithAug 10, 2025
      The UE UNBALANCE ERROR in your LG Washer can occur if the laundry load is too wet at the end of the cycle. To resolve this, rearrange the load to allow proper spinning, then close the door and press the Start/Pause button. It may take a moment for the appliance to begin spinning, as the door must be locked first. Another cause is a load that is too small. Try adding one or two similar items or smaller articles of laundry to help balance the load. Close the door and press Start/Pause button again.
  • M
    Misty OrtizAug 17, 2025
    Why does my LG F4V9BWP2E Washer show a 1E Inlet Error?
    • T
      Tyler BishopAug 17, 2025
      If you are getting a 1E Inlet Error on your LG Washer, it could be due to several reasons: * The water supply might not be adequate. Check another tap in the house to confirm. * The water supply tap may not be fully open. Ensure you open the tap completely. * The water supply hoses could be kinked. Straighten the hose or reinstall it. * The filter of the supply hoses might be clogged. Inspect and clean the filter of the inlet hose. * The drain filter may be clogged. Check and clean the drain filter.
  • V
    Virginia NguyenAug 22, 2025
    What to do if my LG F4V9BWP2E Washer shows a UE UNBALANCE ERROR?
    • K
      Kenneth HigginsAug 22, 2025
      If your LG Washer displays a UE Unbalance Error, it's likely due to an unbalanced load. This can happen for these reasons: * The laundry may be too wet. Rearrange the load to allow proper spinning. Close the door and press the Start/Pause button. It may take a few moments before the appliance begins to spin. The door must be locked before spin can be achieved. * The load might be too small. Add 1 or 2 similar items or smaller articles of laundry to help balance the load. Close the door and press the Start/Pause button. It may take a few moments before the appliance begins to spin. The door must be locked before spin can be achieved.
  • K
    Kimberly ThomasAug 29, 2025
    How to fix 1E INLET ERROR on LG F4V9BWP2E?
    • J
      James CampbellAug 29, 2025
      The 1E INLET ERROR on your LG Washer indicates that the water supply is not adequate. First, check another tap in the house to ensure the water supply is sufficient. Make sure that the water supply tap is fully open. Inspect the water supply hoses for any kinks and straighten them or reinstall the hose. Also, the filter of the supply hoses might be clogged, so check and clean the filter. If water leakage occurs in the aqua stop supply hose, replace it.
  • P
    perryclarkSep 3, 2025
    What to do if my LG Washer shows OE WATER OUTLET ERROR?
    • T
      thomas52Sep 3, 2025
      The OE WATER OUTLET ERROR on your LG Washer means there's an issue with the water draining. This can happen if the drain hose is kinked or clogged, so clean and straighten the drain hose. Also, the drain filter might be clogged. Check and clean the drain filter to resolve this issue.

LG F4V9BWP2E Specifications

General IconGeneral
BrandLG
ModelF4V9BWP2E
CategoryWasher
LanguageEnglish

Related product manuals