LG GR-J34FTKHL User Manual (English)

Questions and Answers:

T
Tracy BurgessAug 19, 2025
Why is my LG GR-J34FTKHL not cold enough?
- L
  Lindsey WilliamsSep 12, 2025
  If your LG Refrigerator isn't cold enough, several factors could be the cause. First, ensure the fridge or freezer temperature isn't set too warm; set it to 'Medium'. Also, check if the refrigerator is in direct sunlight or near a heat source. Make sure you cool hot food before storing it, and avoid overfilling the refrigerator to allow proper air circulation. Finally, ensure the doors are completely closed and that there's enough space around the appliance for ventilation.
R
Robert SteeleAug 21, 2025
Why is my LG GR-J34FTKHL icemaker not working?
- J
  jacksonmarcusAug 21, 2025
  If your LG refrigerator's icemaker isn't producing ice or is producing only a small amount, consider these points. If the refrigerator was recently installed, it takes about 48 hours for ice production to begin. Ensure the water supply pipe is connected and the supply valve is fully open and that the water supply hose isn't bent, which could compromise water flow. If you've recently dispensed a large amount of ice, allow about 24 hours for more ice to be produced. Check that the icemaker switch or button on the control panel is set to ON. The freezer temperature should be at -18 °C for normal operation. Avoid frequent opening of the refrigerator door, and ensure the door is completely closed to maintain the freezer compartment's temperature.
E
Erica BryanAug 23, 2025
Why is there frost in my LG Refrigerator freezer?
- A
  Ashley AustinAug 23, 2025
  If frost has formed in your LG Refrigerator's freezer compartment, ensure the doors are closing properly and that no food items are blocking the door. Always cool hot food before storing it. Make sure the air entry or exit of the freezer compartment isn't blocked, and avoid overfilling the freezer to allow proper air circulation.
T
Tonya CampbellAug 26, 2025
Why is my LG Refrigerator making clicking noises?
- E
  emillerAug 26, 2025
  The defrost control will click when the automatic defrost cycle begins and ends. The thermostat control will also click when cycling on and off. This is normal operation.
D
Danielle PhillipsAug 28, 2025
Why is my LG Refrigerator making rattling noises?
- K
  Katherine OconnellAug 28, 2025
  Rattling noises may come from the flow of appliance, the water line on the back of the unit (for plumbed models only), or items stored on top of or around the appliance. Check if the appliance is resting evenly on the floor. If the compressor does not stop rattling after three minutes, turn the power to the appliance off and then on again.
C
Christine HurleyAug 29, 2025
What causes whooshing noises in my LG GR-J34FTKHL?
- L
  Larry JohnsonAug 30, 2025
  Whooshing noises are normal. The evaporator fan motor is circulating air through the fridge and freezer compartments.
C
courtneyyoungSep 1, 2025
Why is my LG GR-J34FTKHL making gurgling noises?
- A
  asteeleSep 1, 2025
  Gurgling noises are normal, it is just the appliance flowing through the cooling system.
D
Danielle ElliottSep 3, 2025
Why is my LG GR-J34FTKHL Refrigerator making popping noises?
- S
  Shelby OdonnellSep 3, 2025
  Popping noises are due to the contraction and expansion of the inside walls because of changes in temperature. This is normal operation.
R
Robert SchwartzSep 5, 2025
Why is there condensation in my LG GR-J34FTKHL?
- C
  Christopher MayerSep 5, 2025
  Condensation inside your LG Refrigerator can occur for several reasons. Ensure you cool hot food before storing it. If you left the door open, close it, and the condensation should disappear; you can wipe it with a dry cloth. Avoid opening and closing the door too frequently. Store warm or moist food in sealed containers.
M
Monica NormanSep 7, 2025
Why is there frost on the outside of my LG GR-J34FTKHL?
- C
  chowardSep 7, 2025
  Frost or condensation on the inside or outside of your LG Refrigerator can form if the door is opened and closed frequently or is improperly closed, allowing outside air to penetrate. It can also appear if the installation environment is humid. Wipe off any moisture with a dry cloth.