LG LMXS3006 Series User Manual (English)

Questions and Answers:

M
Marcus BrownAug 28, 2025
What to do if my LG LMXS3006 Refrigerator icemaker is not making enough ice?
- L
  Lori HarperAug 28, 2025
  If your LG Refrigerator icemaker isn't making enough ice, check the ice mode setting. If you are in 3 ICE mode, switch to 6 ICE mode for more ice production. Also, make sure your house water supply is connected with adequate pressure and the valve is fully open. Replacing the water filter approximately every six months, when the indicator turns on, when the water dispenser output decreases or when the ice cubes are smaller than normal is recommended. Low house water supply pressure could also be the reason; the water pressure must be between 20 and 120 psi (138 and 827 kPa) on models without a water filter and between 40 and 120 psi (276 and 827 kPa) on models with a water filter.
M
manuelrodriguezAug 27, 2025
Why is water not dispensing from my LG LMXS3006?
- C
  conniephillipsAug 27, 2025
  If your LG Refrigerator is not dispensing water, allow 2.5 gallons of water to flush to remove trapped air and contaminants from the system if it is a new installation or the water line was recently connected. Ensure that the dispenser panel is unlocked by pressing and holding the Lock button for three seconds. Press the Water button on the control panel to ensure it is set for water dispensing. Make sure that the refrigerator or freezer doors are closed properly. If the water filter has been recently removed or replaced, dispense 2.5 gallons of water to remove trapped air and contaminants. Check for any kinks in the tubing connecting the refrigerator to the house supply valve. Finally, confirm that the house water supply is connected and the valve is fully open.
G
Gregory ThomasAug 27, 2025
Why is my LG LMXS3006 icemaker not making enough ice?
- J
  John GatesAug 27, 2025
  If your LG Refrigerator's icemaker is not making enough ice, it could be due to several reasons. The demand may exceed ice production capacity. Ensure the house water supply is connected with adequate pressure and the valve is fully open. Consider replacing the water filter, as it may be exhausted. Low house water supply pressure or a reverse osmosis filtration system can also be factors. Check for kinks in the tubing connecting the refrigerator to the house supply valve. Avoid opening the doors too often or for long periods. Ensure the doors are closed completely and the freezer temperature is at the recommended 0 °F (-18 °C).
S
Samuel BrownAug 26, 2025
Why is my LG Refrigerator not cooling?
- A
  Andrea WilsonAug 26, 2025
  If your LG Refrigerator isn't cooling or has no power, first check your home's main electrical box and replace any blown fuses or reset tripped circuit breakers. If that's not the issue, ensure the refrigerator control isn't set to OFF. Also, check if the refrigerator is in Demo Mode, which disables cooling. If recently installed, allow up to 24 hours to reach the desired temperature. If recently relocated, let it stand upright for 24 hours before plugging it in. Finally, it may be in the defrost cycle; wait 30 minutes after completion to see if the temperature restores.
Z
Zachary MurphyAug 25, 2025
How to adjust the temperature if my LG Refrigerator or Freezer section is too cold?
- A
  Ashley BowenAug 26, 2025
  If your LG Refrigerator or Freezer section is too cold, adjust the temperature control one increment at a time and allow time for the temperature to stabilize.
Y
ydelgadoAug 25, 2025
Why is my LG LMXS3006 not cooling or has no power?
- L
  Laura HernandezAug 25, 2025
  If your LG Refrigerator is not cooling or has no power, check the main electrical box and replace any blown fuses or reset the circuit breaker. Do not increase fuse capacity. If the control is set to OFF, turn it ON. If the refrigerator is in Demo Mode, see the FAQs section of this manual for instructions on how to disable it. Also, the refrigerator may be in the defrost cycle, so wait 30 minutes and confirm the proper temperature has been restored. If the refrigerator was recently installed, it may take up to 24 hours to reach the desired temperature. If it was recently relocated, let it stand upright for 24 hours before connecting it to power.