LG WM2077C - User Manual

Other manuals for LG WM2077C

Questions and Answers:

V
victor97Aug 26, 2025
What to do if my LG WM2077C is leaking water?
- J
  Jenny BrooksAug 27, 2025
  If you notice water leaks from your LG washer, here are some potential causes and solutions: * Check if the fill hose connection is loose at the tap or washer and tighten it. * Ensure that house drain pipes are not clogged. Unclog the drain pipe or contact a plumber if necessary. * Too much or unsuitable detergent can cause leaks. Reduce the amount of detergent or switch to a low-sudsing detergent. * Verify that the water supply is adequate in your area by checking another tap in the house. * Make sure the water supply tap is fully open. * Inspect the water inlet hose for any bends and straighten it. * Check the filter of the inlet hose for clogs. * Examine the drain hose for bends or clogs and clean and straighten it. * Clean the drain filter if it is clogged.
C
Christine LeAug 27, 2025
Why my LG WM2077C does not start?
- M
  Michael MillsAug 27, 2025
  If your LG Washer doesn't start or won't spin, ensure the power cord is securely plugged into the wall outlet. Check your house fuse or circuit breaker, and reset it if necessary. Make sure the water supply tap is turned on. Also, verify that the door is firmly shut; press the Start/Pause button, keeping in mind that it may take a few moments for the washer to begin spinning after the door locks.
M
mooregrantAug 27, 2025
What to do if my LG WM2077C Washer is leaking?
- R
  Richard HendersonAug 28, 2025
  If you're experiencing water leaks with your LG Washer, or if water isn't entering or draining properly, check the fill hose connections at the tap and washer and tighten them if loose. Ensure your house drain pipes are not clogged, and contact a plumber if needed. Reduce the amount of detergent you're using, or switch to a low-sudsing detergent if you notice excessive suds. Confirm that your water supply is adequate by checking another tap in the house and fully opening the water supply tap. Straighten any bent water inlet hoses and check the filter of the inlet hose. Finally, inspect the drain hose for any bends or clogs, and clean the drain filter if it's clogged.
C
Cindy ThomasAug 28, 2025
What does LOCKED MOTOR ERROR mean on my LG WM2077C?
- D
  Debra MannAug 28, 2025
  A LOCKED MOTOR ERROR can occur for several reasons: the connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector (3-pin, female, white) of STATOR ASSEMBLY; the electric contact between the connectors (3-pin, male, white) in the MOTOR HARNESS and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable; the MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open circuited); or the hall sensor is out of order/defective.
L
lauramuellerAug 29, 2025
How to fix rattling noise in LG WM2077C?
- M
  mhuynhAug 29, 2025
  If your LG Washer is making rattling, clanking, thumping, or vibrating noises, stop the washer and inspect the drum and drain filter. If the noise continues after restarting, it may require service. If the sound persists, the washer might be unbalanced; stop it and redistribute the wash load. Ensure all four leveling feet are firmly in contact with the floor during the spin cycle.
M
michaelsmithAug 30, 2025
Why does my LG WM2077C show an IMBALANCE ERROR?
- E
  englishjessicaAug 30, 2025
  An imbalance error on your LG washer can occur if the load is too small, the appliance is tilted, laundry is gathered to one side, or non-distributable items are in the drum.
T
Traci GayAug 23, 2025
What does a DRAIN ERROR mean on my LG WM2077C Washer?
- B
  Brittney GarciaAug 23, 2025
  A DRAIN ERROR on your LG washer means that the water hasn't fully drained within 10 minutes.
J
Joshua BurkeSep 1, 2025
What causes a LOCKED MOTOR ERROR on an LG WM2077C Washer?
- A
  Adam PorterSep 1, 2025
  A LOCKED MOTOR ERROR on your LG Washer can be caused by several issues: * The MOTOR HARNESS connector is not connected to the STATOR ASSEMBLY connector. * Poor electrical contact between the MOTOR HARNESS and the MAIN PWB ASSEMBLY connectors. * A cut in the MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY. * A defective hall sensor.
K
Kelsey JohnsonSep 2, 2025
What does WATER INLET ERROR mean on my LG WM2077C?
- W
  William HernandezSep 2, 2025
  A WATER INLET ERROR on your LG washer means that the correct water level isn't reached within 8 minutes after water is supplied, or it doesn't reach the preset water level within 25 minutes.
B
Bryan SilvaSep 2, 2025
What causes an OVER CURRENT ERROR on my LG WM2077C Washer?
- D
  David WilliamsSep 3, 2025
  An OVER CURRENT ERROR on your LG Washer can be caused by a faulty MAIN PWB ASSEMBLY or a short-circuited winding in the STATOR ASSEMBLY.