To Next PageTo Next PageWhat does "P" mean on my Like It Garage Door Opener display with the motor led flashing?
The "P" displayed with the motor LED flashing indicates an electronic card error. Contact the supplier for a replacement.
What to do if my Like It Garage Door Opener remote control does not have range?
If your remote control's range is limited, the battery might be dead. Try replacing the remote control battery. Alternatively, there might be interference or a damaged receiver. In this case, consider purchasing an external receiver and placing it away from the source of interference.
What to do if my Like It PRO600 door does not close completely?
If the garage door isn't closing all the way, it might be due to insufficient closing force, an incorrectly programmed motor course, or badly adjusted side hinges. Try adjusting the closing force, adjusting the motor's course, or setting a gap to side hinges.
Why my Like It Garage Door Opener motor doesn't work when I press the remote control button?
If the Like It Garage Door Opener motor doesn't work when you press the remote button, here's what to check: * **Remote Control Battery:** Ensure the remote control battery is working. * **Fuse:** Replace the fuse if it has blown. * **Remote Control Damage:** Try another remote or the motor control buttons. * **Remote Control Deprogramming:** Reprogram the motor limit switches and relieve some strength that the motor does in the closed position. * **High Closing Force/Door Lock/Photocells:** See points 5.8 and 5.6 in the manual.
Why Like It Garage Door Opener remote control does not have range?
If your Like It Garage Door Opener remote control has a short range: * **Battery:** Replace the remote control battery. * **Receiver Damage/Interference:** Purchase an external receiver and place it away from any interference.
What to do if Like It Garage Door Opener door stops during opening?
If your Like It Garage Door Opener door stops while opening, it could be due to: * **Insufficient Opening Force:** Try adjusting the opening force. * **Heavy Door:** Adjust the opening force to compensate for the door's weight. * **Motor Power/Course:** Adjust the course of the motor.
Why does my Like It Garage Door Opener only starts to open 2 seconds after pressing the command button?
The delay in opening could be due to the Pre-Flash function being enabled. See paragraph 5.9 for more information.
Why Like It Garage Door Opener setting position not saved?
The setting position might not be saved because the door setup for opening and/or closing is in an improper position, the springs are incorrectly balanced, or the door is badly adjusted. Verify the number of turns in the torsion spring (see the CE label), verify if the door works manually, and adjust the door if needed. You can also set a gap to side hinges. If the door is working with too much effort, increase the engine power (chapter 5.5) one more level.
How to fix noisy chain in Like It PRO600 Garage Door Opener?
A noisy chain could be caused by it being too loose or the motor rail not being aligned with the door's center. Try tightening the chain or aligning the motor rail with the center of the door.
What does "H" mean on my Like It Garage Door Opener display?
The "H" on the display indicates that the Shunt is missing on the board, so check / place the Shunt (unless you have a Pass door). It could also indicate a gearmotor anomaly, in which case contact the supplier for replacement.
General| Brand | Like It |
|---|---|
| Model | PRO600 |
| Category | Garage Door Opener |
| Language | English |
Essential safety instructions and precautions for installing and using the garage door operator.
Lists the necessary tools and parts required for the motor installation process.
Describes how the single button controls open, stop, and close actions for the operator.
Highlights DC motor benefits like low noise, soft start, and slow stopping.
Explains the LED display for working status and the rolling code decoding.
Ensures door opening and closing in manual mode without electricity.
Lists optional features like photocells, wall push-button, and digicode.
Steps to prepare the operator and door for programming the limit switches.
Procedure to set the door's fully open and closed positions using the control panel.
Instructions for coding new remote controls, push buttons, or digicodes.
Procedures for handling full memory capacity and erasing stored codes.
Guide on how to adjust the opening and closing force levels if necessary.
Steps to enable or disable the photocell safety function.
How to activate or deactivate the auto-close feature using safety devices.
Setting the 'Condominium Function' for specific door behavior with remote control.
Details on how to use the manual release handle for door operation during power failure.
Information on how the door remains closed when the motor is removed.
Important warnings regarding children's safety, door maintenance, and hazards.
