Lilytech ZL-7903A - Controller Configuration; Parameter Table

Suzhou Lily Tech Co., Ltd.
Page 4, Total 8 Pages
Parameter Table
Code
Function
Range
Unit
Indication
Default
T10
Temperature control working mode
0 ~ 2
0: R1 up/down limit control
1: External SSR, up/down limit control
2: External SSR, PID control
0
T11
Temperature set point
0.0 ~ 100.0
℃/℉
37.8
T12
Temperature hysteresis for R1 (T10 = 0)
0.0 ~ 20.0
℃/℉
Relative to T11, absolute value: T11 - T12
0.2
T13
Temperature hysteresis for SSR (T10 = 1)
0.0 ~ 20.0
℃/℉
Relative to T11, absolute value: T11 - T13
0.3
T14
Min stop time for temperature load (R1)
0 ~ 999
sec
1
T20
Temperature calibration
-9.9 ~ +9.9
℃/℉
0.0
T21
High temp. alarm relative point
0.0 ~ 65.0/dis
℃/℉
dis: disable warning. Absolute point = T11 + T21
dis
T22
Low temp. alarm relative point
0.0 ~ 65.0/dis
℃/℉
dis: disable warning. Absolute point = T11 - T22
dis
T25
High temp. protection relative point
0.0 ~ 65.0/dis
℃/℉
dis: disable warning. Absolute point = T11 + T25
Ref.: U20 = 1/2/3, U30 = 1/2/3, U40 = 1/2/3
0.2
T26
Hysteresis for T25
0.0 ~ 65.0
℃/℉
Absolute point = T11+T25-T26
Ref.: U20 = 1/2/3, U30 = 1/2/3, U40 = 1/2/3
0.1
T30
Proportion of SSR PID
0.1 ~ 5000
Power/℃
Kp for PID
39.3
T31
Integration of SSR PID
0 ~ 5000
sec
Ti for PID. If Ti = 0, shut integration.
15.7
T32
Differential of SSR PID
0 ~ 5000
sec
Td for PID. If Td =0, shut differential.
40.5
H10
Dehumidify / humidify mode
0 / 1
0: dehumidify, 1: humidify
1
H20
Humidity set point
0 ~ 99
%RH
50
H21
Humidity hysteresis
0 ~ 50
%RH
Relative to H20, absolute value: H20 - H21
5
H22
Humidity calibration
-9.9 ~ +9.9
%RH
0.0
H23
Minimum stop time for humidity load (R3)
0 ~ 30
min
0
H24
High humidity warning relative point
0 ~ 80/dis
%RH
dis: disable warning. Absolute point = H20 + H24
dis
H25
Low humidity warning relative point
0 ~ 80/dis
%RH
dis: disable warning. Absolute point = H20 - H25
dis
H26
High humidity protection relative point
0 ~ 80/dis
%RH
dis: disable warning. Absolute point = H20 + H26
Ref.: U20 = 1/2/3, U30 = 1/2/3, U40 = 1/2/3
5
H27
Hysteresis for H26
0 ~ 80
%RH
Absolute point = H20-H26-H27
Ref.: U20 = 1/2/3, U30 = 1/2/3, U40 = 1/2/3
2
U10
Left turn (R6) time unit
1 ~ 2
1: minute, 2: hour
1
U11
Left turn (R6) time of the timer
1 ~ 999
120
U12
Right turn (R7) time unit
1 ~ 2
1: minute, 2: hour
1
U13
Right turn (R7) time of the timer
1 ~ 999
120
U14
Turning times
0 ~ 999
0: unlimited turning times
0
U16
Turning motor working mode
0 / 1
0: Either R6 or R7 will be energized.
Need position switches, position arrival shuts off
the power supply to motor
1: Only energized during turning moment (U17).
Manual egg turning support
1
U17
Motor being energized time for every turning
0 ~ 999
sec
Effective only when U16 = 1
30
U18
Hatching days
0 ~ 99
day
0: disabled hatching days counting
0
U20
Output R5 (air exhaustion) control mode
0 ~ 3
0: Air exhaust
1: Air exhaust + humi./temp. high limit protection
2: Air exhaust + temperature high limit protection
3: Air exhaust + humidity high limit protection
1
U21
Time unit for air exhaust period (R5)
0 ~ 2
0: second, 1: minute, 2: hour
1
U22
Air exhaust period (R5)
1 ~ 999
30
U23
Time unit for air exhausting time (R5)
0 ~ 2
0: second, 1: minute, 2: hour
0
U24
Air exhausting time (R5)
1 ~ 999
30
U30
Output R4 (Lamp or protection) control mode
0 ~ 3
0: illumination control
1: temperature and humidity high limit protection
2: Temperature high limit protection
3: humidity high limit protection
0
U34
Output R4 delay time for automatic shutdown
1 ~ 999
Min
Only effective when U30 = 0
2
U40
Output R8 (alarm or protection) control mode
0 ~ 3
0 = alarm output
1 = temperature and humidity High limit protection
2 = temperature high limit protection
3 = humidity high limit protection
0
U50
Door switch mode
0 / 1
0: Normal close, 1: Normal open
0
U65
Buzzing warning option
0 / 1
0: disable warning, 1: enable warning
1
U90
Password
000 ~ 999
000 = no password
0
U93
PID self auto tune power rate
10 ~ 100
%
Percent of heater’s full power rate
50