Need help?Do you have a question about the Linn Majik-I and is the answer not in the manual?
General| Type | Integrated Amplifier |
|---|---|
| Phono Stage | MM |
| Total Harmonic Distortion | <0.01% |
| Input Sensitivity | 200 mV |
| Input Impedance | 47 kOhms |
| Signal-to-Noise Ratio | >100 dB |
| Inputs | 1 x Phono (MM, RCA) |
Explains symbols used for safety warnings and important information within the manual and on the apparatus.
CAUTIONary notes on reducing electric shock risk, including not removing covers and referring servicing to qualified personnel.
Details on non-rewireable mains plugs and correct wiring for Live, Neutral, and Earth pins.
Advises on safe placement away from water, heat, and ensuring proper ventilation to avoid overheating.
Details on plug safety, power sources, and outdoor antenna grounding for electrical safety.
Covers cleaning, cord protection, accessory usage, unplugging during storms, servicing, mounting, and climate suitability.
Detailed steps for replacing the fuse in the UK mains plug, emphasizing correct fuse type and fitting.
Guide for safely replacing a mains plug, including wiring and cable restraint instructions.
Explains the Chakra amplifier design using transistors for enhanced performance and efficiency.
Details the benefits of the SMPS, such as size, efficiency, and cleaner mains supply.
Explains Aktiv operation, which uses SMPS-powered crossovers for improved audio signal delivery.
Describes over-current and over-temperature protection mechanisms that shut down the amplifier when necessary.
Lists the accessories included with the Majik-I and recommends keeping packaging for transport.
Advises on optimal placement for ventilation and heat dissipation, including required clearance.
Recommends siting the amplifier away from other electronic devices to prevent interference.
Explains MM, MC, and line-level input options and the need for retailer reconfiguration.
Explains how the amplifier's protection circuits operate during overheating or overload, and recovery time.
Identifies and describes all ports and connectors on the Majik-I's back panel.
Instructions for connecting devices like CD players, tuners, or tape decks to line-level inputs.
Guide to connecting a turntable, including phono stage setup and earth ground connection.
How to use PRE OUT to connect to an external power amplifier for increased power.
How to use TAPE OUT to connect to a tape deck or other analogue recording device.
Details how to connect loudspeakers using binding posts, banana plugs, or spade terminals.
Instructions for connecting headphones to the front panel jack, noting speaker muting.
How to connect portable audio sources like MP3 players via the AUX input.
Crucial steps for connecting the unit to the mains supply, emphasizing earthing and automatic voltage selection.
Identifies and describes each control on the Majik-I's front panel for direct operation.
Explains the remote handset, its LEDs, basic controls, and mode switching for product control.
Details how to put the unit into standby, toggle modes, and recommended practices for longer periods of non-use.
Instructions on selecting sources, adjusting volume, muting, and using volume/audio adjustments.
Covers adjusting audio balance and setting up recording paths via TAPE OUT.
Explains how to access and navigate the unit's setup menus using the handset or front panel controls.
Details settings for display brightness, content, and timeout behavior.
Allows customization of input names, types, and volume offsets for each source.
Settings for volume rate, mute rate, volume limit, volume preset, and headphone volume offset.
Settings for selection timeout, startup source, standby recording, handset commands, and RS232.
Options to save, restore, or reset settings, and view unit information like software revisions.
Details input/output impedances, signal-to-noise ratios, channel separation, and connector types.
Lists gain range, harmonic distortion, frequency response, power consumption, and mains voltage.
Provides unit dimensions, weight, shipping information, and control methods.
Explains warranty terms, registration, and the importance of keeping the sales receipt.
Provides contact details for technical support via local retailers or Linn offices.
To Next Page
