To Next PageTo Next PageWhy won't the blower run on my Lopi Leyden?
The blower on your Lopi Wood stove might not be running because the stove isn't hot enough yet; it usually takes 15 to 30 minutes for the stove to reach temperature. Another reason could be that electricity is cut to the blower. Check the household breaker or fuse to ensure it's working.
What to do if kindling does not start in my Lopi Leyden Wood stove?
If the kindling in your Lopi Wood stove isn't starting and the fire is smoldering, you may not be using enough starter paper; use additional newspaper if necessary. Also, try opening the bypass and the air control. If the flame is not getting enough air, a small crack in the door is all that is needed.
Why does smoke enter the room when I start my Lopi Leyden?
Smoke might enter the room during start-up of your Lopi Wood stove because of a cold air blockage. To resolve this, burn a piece of newspaper to establish a draft. Also, ensure that the bypass and air control are open. If the flame isn't getting enough air, even a small crack in the door might help.
What to do if my Lopi Wood stove does not burn hot enough?
If your Lopi Wood stove isn't burning hot enough, it could be due to wet wood. Also, ensure the air control is fully open and slide it back and forth to make sure it is not stuck. Insufficient draft can also cause this problem; adding more pipe or a draft-inducing cap may help.
Why does smoke enter the room when reloading my Lopi Wood stove?
If smoke enters the room while reloading your Lopi Wood stove, it could be due to insufficient draft. Adding more pipe or a draft-inducing cap may help. Before opening the door, open the bypass and air control. You can also try opening the loading lid 1 inch to let air enter the firebox for a few seconds before fully opening it.
General| Fuel Type | Wood |
|---|---|
| EPA Certified | Yes |
| Maximum Log Size | 24 inches |
| Construction | Steel |
| Blower Included | Optional |
| Material | Steel |
| Finish | Porcelain Enamel |
| Type | Wood stove |
| Heating Capacity | 1, 000 - 2, 000 Sq. Ft. |
| Maximum Burn Time | Up to 10 Hours |
Provides key details on warranty, serial numbers, and dealer contacts for Lopi pellet stoves.
Details performance metrics like heating area, burn rate, and maximum burn time.
Shows the physical size and measurements of the pellet stove.
Lists voltage, amperage, and wattage requirements for the stove's operation.
Specifies approved fuel types for the heater and preparation guidelines.
States the heater's compliance status with environmental regulations.
Emphasizes reading the manual and checking local regulations before installation.
Itemizes all components included with the pellet stove package.
Lists various configuration choices for setting up the pellet stove.
Advises on site assessment, layout, and verification of dimensions for the stove.
Defines safe distances and positioning requirements for the pellet heater.
Specifies the need for a non-combustible floor protector under the stove.
Details minimum safe distances for straight vent runs from the stove.
Details minimum safe distances for corner vent configurations.
Explains requirements for connecting the exhaust system to the stove.
Illustrates the permissible limits for vent length and height.
Specifies the required diameter and type of venting material for the stove.
Provides instructions for connecting vent sections and ensuring airtightness.
Details where and how the vent system must exit the building safely.
Lists specific safety and installation rules for mobile homes.
Explains the need and method for connecting external combustion air.
Sets specific clearance rules for installing the stove in confined alcove spaces.
Guides on installing internal baffles for proper airflow and combustion.
Instructs on checking the door's seal for proper function and airtightness.
Explains how to adjust the airflow to the firepot for optimal burning.
Details how to connect and install the room thermostat for temperature control.
Illustrates a common method of venting the stove directly through an exterior wall.
Shows a vertical venting setup for the pellet stove through the ceiling.
Depicts connecting the stove's vent system to a Class A chimney.
Shows the process of installing the stove within a masonry fireplace.
Illustrates installation in a zero-clearance metal fireplace.
Depicts venting the stove through a separate freestanding masonry chimney.
Reiterates critical warnings to ensure safe operation of the pellet stove.
Identifies the control panel and its various functions for stove operation.
Guides initial startup, including paint curing and first burn procedures.
Explains the correct procedure for filling the stove's pellet hopper.
Describes the manual and automatic control modes for the pellet stove.
Details how to operate the stove using manual controls and settings.
Explains how the stove operates automatically with a connected thermostat.
Explains how to fine-tune airflow to the firepot for optimal burning.
Guides on modifying the fan speed to control heat output and airflow.
Explains the automatic sequence the stove follows when starting.
Describes the indicator light that signals the auger motor is active.
Explains the warning light and provides troubleshooting codes for maintenance issues.
Describes the function of the manual auger control button.
Provides guidance on stove behavior and safety during power interruptions.
Details safe and effective use of mixed fuels, including proportions and preparation.
Advises on visually checking the flame and burn pattern for optimal performance.
Guides on diagnosing and preventing pellet overflow in the firepot.
Explains how to identify and address ash clinkers in the firepot.
Provides step-by-step instructions for cleaning the primary burn area.
Details the safe procedure for opening the stove's access door.
Describes methods for clearing ash residue from the stove's internal components.
Instructs on cleaning the pellet storage area to remove dust and debris.
Guides on cleaning internal heat transfer components for efficiency.
Details how to remove and clean the internal baffles for ash removal.
Explains how to move accumulated ash to the collection tray.
Guides on checking the ashpan and safely disposing of its contents.
Provides instructions for cleaning the glass on the stove's door.
Explains the causes and importance of cleaning combustion byproducts.
Details cleaning procedures for the vertical exhaust venting system.
Guides on cleaning the exhaust fan assembly and surrounding area.
Instructs on cleaning the room air circulation fan for optimal performance.
Details inspection and cleaning of the exhaust vent pipe and cap.
Explains how to properly align the stove door and adjust the latch.
Guides on identifying and sealing air leaks around the door, glass, and ashpan.
Lists available parts for ordering and replacing components on the stove.
