What to do if my Lopi Wood stove does not burn hot enough?
If your Lopi Wood stove does not burn hot enough, ensure the air control is fully open by sliding it back and forth to ensure it's not stuck. Also, make sure that you are using dry wood. Insufficient draft may also cause this issue, so adding more pipe or a draft-inducing cap may help.
Why won't the blower run on my Lopi Answer?
The blower on your Lopi Wood stove may not run because the stove is not yet up to temperature; it will typically activate after 15 to 30 minutes. If the stove is hot and the blower still isn't running, check your household breaker or fuse to ensure it is working.
What to do if smoke enters the room while reloading my Lopi Answer?
If smoke enters the room while reloading your Lopi Wood stove, first open the air control before opening the door. Allow the air to stabilize before fully opening the door. Open the door approximately 1 inch, letting air into the firebox for a few seconds. Once the smoke appears to flow up the chimney consistently, you can fully open the door. Insufficient draft due to chimney height or outside conditions can also cause this; adding more pipe or a draft-inducing cap may help.
How to stop smoke from entering the room during start-up of my Lopi Answer?
To stop smoke from entering the room during the start-up of your Lopi Wood stove, open the air control. If there is a cold air blockage, burn a piece of newspaper to establish a draft. If the flame is not getting enough air, a small crack in the door is all that is needed.
What to do if my Lopi Answer does not burn long enough?
If your Lopi Wood stove does not burn long enough, make sure the doors are sealing and not allowing air into the firebox. Also, check the ash bed for coals; often, coals are still glowing under a slight bed of flyash. By raking these into a pile you can re-start your stove quickly.
What to do if blower does not run on my Lopi Wood stove?
If your Lopi Wood stove blower isn't running, it might be normal if the stove hasn't reached temperature yet; the blower typically starts after 15 to 30 minutes. Otherwise, check your household breaker or fuse to ensure electricity is reaching the blower.
Why kindling does not start - fire smolders in my Lopi Answer Wood stove?
If your kindling does not start and the fire smolders in your Lopi Wood stove, open the air control. If you don't have enough starter paper, use additional newspaper if necessary. If the flame is not getting enough air, try leaving a small crack in the door to provide more air.
Why my Lopi Answer does not burn long enough?
If your Lopi Wood stove doesn't burn long enough, ensure the doors are sealing properly to prevent air from entering the firebox; see the "Door and Glass Inspection" section on page 35 for details. Also, check the ash bed for coals, as they might be glowing under a layer of flyash; raking them into a pile can help restart the stove.
Why does smoke enter the room while reloading my Lopi Wood stove?
If smoke enters the room while reloading your Lopi Wood stove, open the air control before opening the door. Let the air stabilize before fully opening the door. Open the door approximately 1 inch and let air go into the firebox for a few seconds. Once the smoke appears to be flowing up the chimney consistently, open the door. Another potential cause is insufficient draft, so adding more pipe or a draft-inducing cap may help.
Why does kindling not start and fire smolder in my Lopi Wood stove?
If the kindling does not start and the fire smolders in your Lopi Wood stove, open the air control. If you do not have enough starter paper, use additional newspaper. If the flame is not getting enough air, a small crack in the door is all that is needed.
Overview of the appliance and manual's purpose.
Details on serial number and warranty registration.
Essential safety guidelines for operation and installation.
Additional safety advice and critical warnings.
Lists installation types and key appliance features.
Details on heating capacity, efficiency, and emissions.
Physical measurements of the stove.
Critical safety notice and planning guidance.
Steps for preparing the stove and overview of installation types.
Requirements for stove placement and floor covering.
Standards for factory chimneys and optional equipment.
Rules for chimney exit and outside air requirements.
Specific requirements for alcove installations.
Special requirements for mobile home installations.
Visual guides for ceiling installations.
Visual guides for hearth stove connections.
Further visual guides for hearth connections.
Safety warnings and planning for insert installation.
Steps for preparing inserts and types of installations.
Clearances and hearth specifications for inserts.
Fireplace size and specific requirements for inserts.
Standards for masonry and zero-clearance fireplaces.
Factors affecting insert draft and leveling bolt installation.
Procedure for installing a block-off plate.
Visuals for positive and direct connections.
Visuals for Z.C. and face seal connections.
Safety notices, paint curing, ash removal, and controls.
Tips for starting, reloading, and burning wood.
Techniques for heat control and overnight burns.
Best practices for efficient operation.
Operation modes, automatic control, and heat regulation.
Importance of dry wood and methods for drying/storage.
Building a shed and choosing wood types.
Tips for buying wood and avoiding prohibited fuels.
Summary of periodic and annual maintenance tasks.
Ash removal, glass cleaning, and brass cleaning.
Inspection, adjustment, and replacement of door components.
Touch-up paint, blower cleaning, and firebrick/baffle checks.
Procedures for replacing internal firebricks and baffles.
Replacing air tubes and list of available parts.
Diagnosing and fixing issues like smoke, heat, and starting fires.
Coverage periods for parts and labor.
Terms, limitations, and what is not covered.
Warnings about labels and requirements for different installation types.
Instructions for installing legs and pedestals.
Connecting outside air and installing the rear blower.
Installing the front blower and outside air boot.
Detailed steps for the outside air boot.
How to fit and install surround panels.
Installing insulation and decorative brass trim.
Installing adjustable telescoping legs.
Attaching the flue adapter for flue exit adjustment.
General| Fuel Type | Wood |
|---|---|
| EPA Certified | Yes |
| Blower Included | Optional |
| Material | Steel |
| Maximum Burn Time | 10 hours |
| Emissions | 2.5 g/h |
To Next Page
