58
13.2 Water Pipe Sizing Chart
PIPE DIAMETER (inches; nominal, actual)
1/2*3/411 1/41 1/222 1/23456
US GPM LPM 0,662 0,82 1,05 1,38 1,61 2,07 2,47 3,07 4,03 5,05 6,06
13,8 10,40,10,02
27,6 3 1,2 0,4 0,10 0,05
311,4 6 2,3 0,7 0,20 0,10
41510 4 1,2 0,32 0,15 0,05
51916 6 1,8 0,48 0,23 0,07
62322 8 2,5 0,67 0,32 0,10 0,04
727
11 3,2 0,89 0,43 0,13 0,06
830
13 3,9 1,07 0,51 0,16 0,07
934 16 4,9 1,3 0,6 0,19 0,08
10 38 19 5,9 1,6 0,8 0,24 0,10 0,04
11 42 23 7,0 1,9 0,9 0,28 0,12 0,04
12 45 26 8,0 2,2 1,0 0,3 0,14 0,05
14 53 11 2,9 1,4 0,4 0,18 0,06
16 61 14 3,7 1,8 0,5 0,23 0,08
18 68 16 4,5 2,2 0,7 0,28 0,10
20 76 20 5,4 2,6 0,8 0,34 0,12 0,03
22 83 23 6,4 3,1 0,9 0,40 0,14 0,04
24 91 28 7,5 3,6 1,1 0,47 0,17 0,05
26 99
9 4,2 1,3 0,54 0,19 0,05
28 106
10 4,7 1,4 0,6 0,22 0,06
30 114 11 5,3 1,6 0,7 0,25 0,07
35 133 15 7 2,1 0,9 0,3 0,09
40 152 19 9 2,7 1,2 0,4 0,11 0,04
45 171 23 11 3,3 1,4 0,5 0,14 0,05
50 190 28 13 4,0 1,7 0,6 0,17 0,06
55 208 16 4,7 2,0 0,7 0,19 0,07
60 227 18 5,5 2,4 0,8 0,23 0,08 0,03
65 246 21 6,3 2,7 1,0 0,26 0,09 0,04
70 265 24 7,2 3,1 1,1 0,30 0,10 0,04
75 284 8 3,5 1,2 0,34 0,12 0,05
80 303
9 3,9 1,4 0,38 0,13 0,05
85 322
10 4,4 1,6 0,42 0,14 0,06
90 341 11 4,8 1,7 0,47 0,16 0,07
95 360 12 5,3 1,9 0,51 0,18 0,07
100 379 14 5,8 2,1 0,56 0,19 0,08
150 569 28 12 4,3 1,2 0,39 0,17
200 758 20 7,1 1,9 0,66 0,27
FLOWRATE
Don’t cheat yourself with undersized pipe! Use
this chart to determine the additional head
imposed on your pump due to pipe friction,
based on flow rate, pipe size and pipe length.
Consider the TOTAL pipe length from the pump
to the pipe outlet to the tank.
Pipe fittings impose additional friction loss. A
sharp 90° pipe elbow adds friction
approximately equal to 6 feet (2m) of pipe of
the same size.
Friction Loss in Plastic Pipe with Standard Inside Diameter (SIDR)
Head Loss from friction in vertical m/ft per 100 m/ft of pipe
Type LPM GPM Type LPM GPM
HR-03H 8 2,2 HR-14 42 11
HR-04 / H 13 3,5 HR-20 58 15
HR-07 20 5 C-BF-04 122 32
HR-10 32 8 C-DF-03 167 44
PEAK FLOW RATE for pipe sizing
*)1/2 data applies to
polyethylene pipe only.
PVC has smaller ID of
0.612”
SHADED VAL-
UES are veloci-
ties over 5 ft per
second and
should be
selected with
caution