LS ELECTRIC H100+ Series

Need help?

Do you have a question about the LS ELECTRIC H100+ Series and is the answer not in the manual?

Summary

Quick Start Reference

Verify & Identify the delivery

Check nameplate for correct VFD delivery and identify product details.

Mounting Instruction

Ensure sufficient space for cooling and proper installation clearances.

Wiring the VFD: Power

Main circuit terminal arrangement for power connections on the drive.

Wiring the VFD: Control

Control circuit terminal arrangement on the drive and switch descriptions.

Keypad: Description

Description of keypad keys and their functions for operating the inverter.

Keypad Navigation and Parameter Changes

Navigate and select parameters using directional arrows in PAR Mode.

Verify Motor Direction

Check motor direction by running the motor at low speed in HAND mode.

HAND; AUTO; OFF keys

Control Wiring

Wiring examples for run command and frequency reference in AUTO Mode.

EZ Start

Basic Setup

Basic drive and motor parameter setup according to application.

Application Setup

Steps to configure application-specific settings like PID function and unit scaling.

3. Setpoint, Feedback Scaling

5. Lost Feedback Detection Mode

6. High;Low Feedback Detection

Safety Information

Safety information

General safety instructions regarding electrical shock and handling.

Preparing the Installation

1.1 Product Identification

1.2 Part Names

1.3 Installation Considerations

Ideal operating and installation conditions for inverter lifespan and reliability.

1.4 Selecting and Preparing a Site for Installation

Points to consider when selecting an installation location, including clearances.

1.5 Cable Selection

Guidelines for selecting appropriate power and signal cables for safe operation.

Signal (Control) Cable Specifications

Installing the Inverter

Installation Flowchart

2.1 Mounting the Inverter

Procedures for mounting the inverter on a wall or inside a panel.

2.3 Cable Wiring

Detailed information and warnings before carrying out wiring connections.

Step 1 Terminal Cover and Cable Guide

Step 2 Ground Connection

Instructions to locate and connect the ground cable to the terminals.

Step 3 Power Terminal Wiring

Terminal layout on the power terminal block and wiring instructions.

Step 4 Control Terminal Wiring

Detailed layout of control wiring terminals and control board switches.

Step 5 PNP;NPN Mode Selection

Step 6 Disabling the EMC Filter for Power Sources with Asymmetrical Grounding

Step 7 Re-assembling the Covers and Routing Bracket

2.4 Test Run

Procedures to test the inverter after installation, including motor rotation check.

Verifying the Motor Rotation

Perform Basic Operations

3.1 About the Keypad

3.1.1 Operation Keys

3.1.2 About the Display

3.1.3 Display Modes

Parameter Setting Mode

3.2 Learning to Use the Keypad

3.2.2 Operation Modes

How to switch between HAND, AUTO, and OFF modes for inverter operation.

3.2.3 Switching between Groups in Parameter Display Mode

3.2.5 Navigating through the Codes (Functions)

3.2.6 Navigating Directly to Different Codes

3.2.7 Parameter Settings available in Monitor Mode

3.2.8 Setting the Monitor Display Items

3.2.9 Selecting the Status Bar Display Items

3.3 Fault Monitoring

How to monitor faults and view trip information.

3.3.1 Monitoring Faults during Inverter Operation

3.3.2 Monitoring Multiple Fault Trips

3.4 Parameter Initialization

Table of Functions

4.1 Drive Group (DRV)

Parameters for basic operation, jog, torque boost, and motor evaluation.

4.2 Basic Function Group (BAS)

4.4 Control Function Group (CON)

4.5 Input Terminal Group (IN)

4.6 Output Terminal Block Function Group (OUT)

4.7 Communication Function Group (COM)

4.8 Gro PID Function Group(PID)

Parameters for PID control, setpoint, feedback, and sleep mode.

4.12 Application 4 Function Group (AP4)

4.13 Protection Function Group (PRT)

Parameters for various protection functions like over/under load, phase loss, thermal protection.

Technical Specification

6.1 Input and Output Specifications

Electrical specs for input/output, including voltage, current, and frequency.

6.3 External Dimensions

6.4 Peripheral Devices

6.5 Fuse and Reactors Specifications

6.6 Terminal Screw Specifications

6.7 Dynamic braking unit (DBU) and Resistors

6.7.1 Dynamic braking unit (DBU)

6.7.3 Dynamic Braking (DB)Unit & DB resistor basic wiring

6.7.4 Dimensions

6.7.6 DB Resistors

6.8 Inverter Continuous Rated Current Derating

Derating based on carrier frequency, input voltage, and ambient temperature.

Applying Drives to Single-phase Input Application

7.1 Introduction

7.2 Power(HP), Input Current and Output Current

Derating requirements for output current and horsepower due to single-phase input.

7.3 Input Frequency and Voltage Tolerance

7.4 Wiring

Instructions for connecting single-phase input power to the inverter terminals.

7.5 Precautions for 1-phase input to 3-phase drive

Key precautions for single-phase input, including reactor use and parameter settings.