EasyManua.ls Logo

Luminous 3KVA - User Manual

Default Icon
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1KVA/ 2KVA/ 3KVA
INVERTER / CHARGER
User Manual

Table of Contents

Questions and Answers

  • M
    Michael CoxAug 8, 2025
    What to do if my Luminous 3KVA Inverter is beeping continuously and the red LED is on?
    • D
      Diane GuzmanAug 8, 2025
      A continuous beep and a red LED on your Luminous Inverter usually indicates a problem. This could be due to several reasons: * The inverter might be overloaded (more than 110% load). Try reducing the load by switching off some equipment. * There may be a short circuit in the output. Check the wiring and remove any unusual loads. * The internal converter component's temperature might be too high (over 120°C). Ensure the unit's airflow isn't blocked and the ambient temperature isn't too high. * The battery voltage may be too high. Verify that the battery specifications and quantity meet the requirements. If none of these steps resolve the issue, it may be necessary to return the inverter to a repair center.
  • B
    Benjamin JonesAug 14, 2025
    Why does my Luminous Inverter work in battery mode even when mains exist?
    • J
      Jonathan NelsonAug 14, 2025
      If your Luminous Inverter continues to operate on battery power despite the availability of mains power, there are a few potential causes: * The input protector might be tripped. Check if the AC breaker has tripped and ensure the AC wiring is properly connected. * The quality of the AC power (from shore or generator) may be insufficient. Check if the AC wires are too thin or too long. * The solar power may be set as the priority output source. Change the output source priority to 'Utility first'.
  • D
    Dennis CareyAug 20, 2025
    What to do if Luminous Inverter shuts down automatically during startup?
    • A
      Alexander RiveraAug 21, 2025
      If your Luminous Inverter shuts down automatically during startup, it could be due to the following reasons: * The battery voltage is too low (less than 1.91V/Cell). Try recharging the battery. * The battery might need to be replaced.
  • L
    Lauren AnthonyAug 27, 2025
    What to do if there is no response after powering on my Luminous 3KVA Inverter?
    • R
      Rachel BennettAug 27, 2025
      If your Luminous Inverter doesn't respond after you power it on, consider these potential causes: * The battery voltage might be extremely low (less than 1.4V/Cell). Check the connections of the batteries and wiring to make sure they are well connected. * The battery polarity may be connected in reverse. Recharge the battery. * The battery might need replacement.
  • Y
    yhudsonSep 1, 2025
    What to do if the internal relay of my Luminous Inverter is switching on and off repeatedly?
    • E
      Emily ReidSep 1, 2025
      If the internal relay of your Luminous Inverter is repeatedly switching on and off when you turn it on, it might be due to a disconnected battery. Check the battery wires to ensure they are properly connected.

Summary

Safety Instructions

General Safety Instructions

Contains crucial instructions for safe installation and operation, including warnings and precautions.

Installation

Mounting the Unit

Provides guidelines for selecting an installation location and ensuring proper clearance and ventilation.

Battery Connection

Explains how to connect batteries, including cable size, terminals, and polarity.

AC Input;Output Connection

Details AC wiring requirements, cable sizes, terminal connections, and precautions.

PV Connection

Provides instructions for connecting PV modules, including cable size and torque.

Operation

Power ON;OFF

Describes how to turn the unit on and off using the power switch.

Operation and Display Panel

LCD Display Icons

LCD Setting

Details how to access and configure various setting programs via the LCD menu.

Display Setting

Operation Diagrams and Working Conditions

Operation Scenario 1: No Utility

Operation Scenario 2: No Solar

Operation Scenario 3: Utility and Solar Present

Operation Scenario 4: No Utility or Solar

Operation Scenario 5: Utility and Solar Present (Utility Charging)

Operation Scenario 6: Solar Charging, Utility Output

Operation Scenario 7: Both Charging, Solar;Battery Output

Operation Scenario 8: Both Charging, Utility Output

Operating Mode Description

Fault and Warning Indicators

Fault Reference Code

Lists fault codes, their corresponding events, and the associated icon display.

Warning Indicator

Describes warning codes, events, audible alarms, and icon flashing patterns.

Specifications

Trouble Shooting

Luminous 3KVA Specifications

General IconGeneral
Capacity3 KVA
WaveformPure Sine Wave
Output Power2400 Watts
Battery TypeTubular Battery
Frequency50Hz
Transfer Time10ms
Operating Temperature0°C to 40°C
CoolingFan Cooling
ProtectionOverload, Short Circuit, Deep Discharge, Over Charge

Related product manuals