Fo ld Fo ld Fo ld
READ ME FIRST
QUICK INSTALL GUIDE
AC1200 Dual-Band
Wireless Access Point
XAP-810
Includes:
AC1200 Dual-Band Wireless AP
Mounting Brackets and Hardware
PoE Injector and Power Cable
Ethernet Cable
READ ME FIRST - CONTROLLER COMPATIBILITY
This XAP-810 is compatible with the Luxul Wireless Controller for fast, easy
configuration and deployment of wireless networks with multiple APs.
n Note: If you’ll be using this AP with a Wireless Controller, refer to
the Quick Install Guide included with the Wireless Controller for
setup instructions.
AP SETUP AND CONFIGURATION
1
Physical Installation
The XAP-810 access point is designed for simple and ecient installation and
can be located one of three ways. First, the included mount is designed to
attach directly to several dierent regions’ standard electrical boxes. Second,
the XAP-810 may be mounted on a ceiling or wall without a box by using the
included mount as a guide to mark attachment locations. Finally, the XAP-810
can be placed on a flat surface by attaching the included rubber feet
to the mount.
c Caution: Attach the rubber feet to the mount and attach the mount to
the AP for flat surface placement to avoid overheating and failure.
X
Single Access Point Placement: Because the signal generated by the
XAP-810 is omnidirectional, the unit should be located as near as possible to
the center of the desired coverage area.
XAP-810 Single AP Coverage Pattern
X
Multiple Access Point Placement: You may need to experiment with
AP placement to optimize the roaming experience. Place APs to ensure
adequate coverage, but not so far apart that there is no signal overlap.
Adjacent APs should overlap enough that the client device has a good
connection to the AP to which it is currently attached, but also sees the
next-nearest AP. Ideally, roaming clients should see signal strength of
two overlapping APs in the range of -60 to -70 dBm at the midway
point between two APs. To learn more about AP placement, visit
luxul.com/ap-placement.
Ideally, roaming clients should see
signal strength of two overlapping
APs in the range of -60 to -70 dBm at
the midway point between two APs
XAP-810 Multiple AP Coverage and Overlap
n Note: Consider using Ekahau HeatMapper to assist with this process,
available from www.ekahau.com. Luxul also oers an informative
“How-To” video on HeatMapper at luxul.com/how-to-videos.
AP SETUP AND CONFIGURATION CONT.
2
Connecting Ethernet and Power
Ethernet and Power
To apply power and network simultaneously, simply connect one end of an
Ethernet cable to a PoE switch, and the other end to the XAP-810 PoE port.
To connect power and Ethernet separately, first connect an Ethernet cable
from the supplied PoE Injector Data & PWR Out port to the PoE port on
the XAP-810. An Ethernet cable length of up to 300 feet can be used.
Sales
801-822-5450
sales@luxul.com
Technical Support
801-822-5450
support@luxul.com
LUX-QIG-XAP-810-v3 07171703
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
To Next Page
Need help?
General
Weight and Dimensions
