M.T.H. F59PH - User Manual

Questions and Answers

B
Brian JonesSep 23, 2025
How to start PFA when engine is stopped in neutral on M.T.H. Toy?
- P
  Patrick PattersonSep 23, 2025
  Try reactivating the feature by holding down the bell button for three or more seconds on your M.T.H. Toy.
E
Edward TerrellAug 25, 2025
How to fix a distorted horn at low voltages on M.T.H. Toy?
- A
  andersonashleyAug 25, 2025
  If the horn on your M.T.H. Toy sounds distorted at low voltages, it could be that your battery is undercharged or dead. Try recharging the battery as explained in the battery sections.
B
Bradley KaneAug 25, 2025
Why does my M.T.H. Toy have a repeating horn blast after shutdown?
- N
  Nicole SimmonsAug 26, 2025
  A repeating horn blast after shutting down your M.T.H. Toy indicates that the battery is insufficiently charged or dead. Follow the recharging instructions found in the section entitled "Self Recharging Battery Backup System".
H
hoffmanmirandaAug 27, 2025
What to do if the horn doesn’t blow on my M.T.H. Toy?
- A
  Austin WeaverAug 27, 2025
  If the horn on your M.T.H. Toy doesn't blow when you press the whistle button, you may be pressing the button too quickly. Try pressing the whistle button slower, taking approximately 1 second to fully depress the button.
J
Joshua HernandezAug 27, 2025
Why coupler won’t arm or fire open on M.T.H. Toy?
- J
  Jessica Mcdonald MDAug 27, 2025
  If you can't get the coupler to arm or fire open when you press the whistle button on your M.T.H. Toy, you may be pressing the whistle button too quickly. Refer to the third remedy in the horn section above.
C
Christopher MartinezSep 14, 2025
Why does the coupler arm when I try to activate the bell on my M.T.H. Toy?
- G
  garysullivanSep 14, 2025
  Reduce the voltage on the transformer before pressing the whistle button to activate the bell on your M.T.H. Toy. The bell will only come on at 8 volts or less.
D
Diane DiazSep 12, 2025
Why cab chatter sounds don’t play on M.T.H. Toy?
- B
  Bryan SimpsonSep 12, 2025
  The Cab Chatter sounds only play in neutral on your M.T.H. Toy, and Proto-Sounds may be programmed to turn these sounds off.
J
Jacob FoxSep 13, 2025
Why only one coupler functions on my M.T.H. Toy?
- P
  Phyllis HarveySep 13, 2025
  Only one coupler can operate at any one time on your M.T.H. Toy. Use the coupler selection switch on the bottom of the chassis to choose which coupler you want active.
C
Crystal WallerSep 4, 2025
Why does the bell only ring once on my M.T.H. Toy?
- E
  elliottedwardSep 5, 2025
  If the bell only rings once when you press the whistle button to activate it on your M.T.H. Toy, you are trying to ring the bell in RESET instead of neutral. Interrupt the power twice to enter Neutral, set the voltage at 8 volts or less and press the whistle button to activate the bell.
P
Patrick HuffSep 2, 2025
Why won’t my M.T.H. Toy engine lock out?
- D
  david55Sep 2, 2025
  If the M.T.H. Toy engine won’t lock out into Forward, Neutral, or Reverse, even after the short horn blast, you are waiting too long to turn the throttle back on after the short horn blast sounds. The power must be turned back on immediately after the short horn blast sounds or the engine will go back into RESET.