MAAX AKER Series User Manual

GUIDELINES
FOR UNIT
INSTALLATION
Page 1
10023034
These guidelines are recommended by
Aker Plastics Company Inc. (hereafter
“MAAX”) for the proper installation of their
product. A careful review of these procedures
(and any referenced publications) before
starting is important in avoiding unnecessary
problems resulting in an improper assembly
or installation.
NOTE: All drawings in this publication are
typical, and may appear different than the
actual items being installed. In addition,
optional items may be shown on the units
which may not have been ordered on the
unit being installed.
ON WHIRLPOOL EQUIPPED MODELS,
A SEPARATE SET OF INSTRUCTIONS
IS PACKED WITH THE UNIT FOR THE
WHIRLPOOL SYSTEM. READ THEM
BEFORE INSTALLING UNIT!
WARNING!
NEVER LIFT OR HANDLE WHIRLPOOL
BY SYSTEM PIPING AT ANY TIME.
LIFTING THE UNIT BY THE PIPING CAN
CAUSE SYSTEM DAMAGE.
Special Notes to Installer
ÜIt is the sole responsibility of the installer
to determine, prior to the installation, the
requirements necessary for compliance
with all codes involving the unit or the
installation!
ÜAll paperwork packaged with the unit and
any associated options or accessories
should be saved and presented to the
homeowner upon completion of the
installation!
ÜHANDLE THE UNIT BY THE SHELL
ONLY! Never lift any unit by attachments
or piping on the shell.
ÜAll published unit dimensions are for
reference only. Any critical dimensions
required for installation should be taken
directly from the unit being installed!
ÜAny independent changes made to the
unit (or to any options and accessories
supplied with the unit) beyond those
required for normal installation can void
all warranties! (Refer to warranties for
further information.)
Inspection Guidelines
A careful check of the unit should be
conducted upon receipt. Notify your supplier
immediately if any questions or problems are
encountered during this process.
DO NOT INSTALL ANY UNIT
WITHOUT FIRST ADDRESSING
QUESTIONS WHICH ARISE DURING
THE INSPECTION!
Basic Module Check
ü Check that the unit drain corresponds to
the bathroom drain location.
ü Check for unit surface damage.
ü Check unit color for coordination to
other bathroom fixtures.
ü Check for proper options and
accessories.
Whirlpool and Accessories Check
An individual system check list is included
in the assembly and operational guidelines
packaged with whirlpool equipped models
and various accessories. Refer to the listed
publications for further information before
continuing.
Alcove-Style (Flanged) Bath Modules
141082
GT-4260 R
GT-4260 L (shown)
141082
GT-4260
141083
GT-60
141482
GT-4260AP with access panel

MAAX AKER Series Specifications

General

Brand	MAAX
Model	AKER Series
Category	Bathroom Fixtures
Language	English

Summary

Special Notes to Installer

Installer Code Compliance and Responsibility

Installer must determine and ensure compliance with all codes for unit installation.

Handling and Dimensional Accuracy

Handle unit by shell only and use actual dimensions for installation accuracy.

Warranty and Paperwork Management

Save unit paperwork for homeowner and avoid modifications that void warranties.

Inspection Guidelines

Basic Module and Accessory Check

Verify unit drain, surface damage, color coordination, and options/accessories.

Whirlpool System Pre-Installation Check

Check whirlpool system components using separate instructions before installation.

Unit Data and Dimensional Guidelines

Alcove-Style Bath Module Dimensions

Provides detailed dimensions for various alcove-style bath module models.

Model Specifications Table

Details unit surface, sump bottom, dry weight, volume, capacity, and floor loading.

Alcove Framing Guidelines

Framing Dimension Tables

Provides specific framing dimensions (A-F) for different alcove bath module models.

Framing Requirements and Considerations

Details typical framing needs, importance of squareness, levelness, and site variations.

Whirlpool Unit Framing Modifications

Notes mandatory pump access and potential framing adjustments for whirlpool units.

Unit Installation and Securing

Unit Positioning and Leveling

Ensure unit is level, square in the alcove, and apron rests flush on the floor.

Securing the Unit to Framing

Drill pilot holes and secure unit flanges to framing using appropriate screws.

Wall Finishing and Sealing

Use underlayment, furring strips, and waterproof sealant for proper wall finishing.

Unit Surface Care and Maintenance

Surface Cleaning Precautions

Avoid abrasive materials/cleaners; use caution with any cleaner, acid, or solvent on the unit.

Routine Cleaning and Deposit Removal

Wipe excess water after use; use mild cleaners for routine cleaning and specific solutions for stains.

Adhesive Removal and Mat Caution

Use caution when removing adhesives; remove suction mats to prevent surface damage.

Limited Warranty Information

Warranty Coverage and Duration

Express limited warranty for acrylic (25 yrs) and fiberglass (5 yrs) units for personal use.

Warranty Limitations and Exclusions

Excludes damage from misuse, improper maintenance, alteration, or acts of God.

Installer Responsibility and Warranty Service

Owner responsible for proper installation; contact dealer or MAAX for warranty service.