What to do if my MacMah Saw table saw does not start?
If your MacMah Saw does not start, ensure the Motor Cord is plugged into a working electrical outlet. If it is, check the circuit fuse and replace it if blown. Also, verify that the circuit breaker hasn't tripped and reset it if necessary. If the issue persists, the Motor Cord or Switch may be damaged and require replacement.
Why do the fuses or circuit breakers open frequently on my MacMah Saw?
If your MacMah Saw experiences frequent fuse or circuit breaker openings, it could be due to several reasons. The motor might be overloaded, in which case you should feed the workpiece more slowly. The fuses or circuit breakers themselves might be the wrong size or defective, requiring replacement. A dull 10” saw blade can also cause this issue, so replace it if necessary. Lastly, a defective power switch could be the culprit, and you should have it replaced.
What causes my MacMah Saw motor to stall, blow fuses, or trip circuit breakers?
If your MacMah Saw motor stalls, blows fuses, or trips circuit breakers, it could be due to several issues. The motor may be overloaded; request a voltage check from the local power company. A dull 10” Saw Blade can also cause this, so replace it. Check if the fuses or circuit breakers are the correct size and not defective, and replace them if needed. Additionally, feeding the workpiece too rapidly can cause these problems, so feed the workpiece into the 10” Saw Blade more slowly.
Why does the motor on my MacMah Saw overheat?
If the motor of your MacMah Saw overheats, it could be due to the motor being overloaded; request a voltage check from the local power company. Another possible cause is a dull 10” saw blade, which should be replaced. Additionally, sawdust inside the table saw might be blocking airflow, so clean out the saw base.
How to fix excessive vibration in my MacMah Saw?
If your MacMah Saw vibrates excessively, first readjust the Leveling Feet, because the floor surface may be uneven. If the issue persists, the V-belt might be damaged and needs replacement. A damaged 10” saw blade can also cause vibrations, so replace it if necessary. Also, check for any loose bolts, screws, or nuts and tighten all hardware.
What to do if ripping burns the workpiece or stalls the motor on my MacMah Saw?
If, when ripping, the cut burns the workpiece or stalls the motor of your MacMah Saw, the 10” saw blade teeth might be dull, requiring sharpening or replacement. Another cause could be a warped workpiece, which should be replaced. Lastly, the rip fence might not be parallel with the 10” saw blade; realign the rip fence and lock it in position with the Rip Fence Handle.
Why does the power switch on my MacMah Saw not operate?
If the Power Switch on your MacMah Saw does not operate, it could be due to burned-out Power Switch contacts, requiring replacement. Another possibility is a defective capacitor, which also needs to be replaced. Additionally, loose or damaged wiring connections could be the cause, and these should be checked and repaired.
Why is the motor on my MacMah Saw slow and weak?
If the motor of your MacMah Saw is slow or weak, it could be due to low voltage from the source, in which case you should request a voltage check from your local power company. The windings may be burned out or open, requiring the motor to be checked or repaired. A defective power switch can also cause this, so avoid using other appliances on the same circuit. Additionally, the circuit might be overloaded with other equipment, so avoid using other appliances on the same circuit.
What to do if the miter gauge or rip fence on my MacMah Saw doesn't move smoothly?
If the Miter-gauge does not move freely or the Rip Fence does not move smoothly on your MacMah Saw, the miter gauge assembly may be dirty. Loosen the miter gauge knob, then clean and lubricate the Miter Gauge Rod. Alternatively, the Rip Fence might be mounted incorrectly. Remove and reposition the Rip Fence, then lock it in position with the Rip Fence Handle.
Why are the bevel and height handles hard to turn on my MacMah Saw?
If the Bevel or Height Handles are hard to turn on your MacMah Saw, it is likely due to sawdust collecting on the mechanisms inside the base. Clean and lubricate these mechanisms to resolve the issue.
To Next Page
General