35 Series-HST, Model - 3535, 4035, 4535 & 5035
82
Lubrication Oil
Transmission, Hydraulics and Oil Immersed Brakes
Use mild EP type gear lubricant. They should meet API GL4
performance category with suitable additives compatible
for paper based brake liner and taking care of noise. Use
viscosity based on the expected air temperature range
during the period between oil changes.
Please refer Oil Specifications Chart for oil specifications at
different range of ambient temperatures.
Following oils are recommended.
1. GULF Universal Tractor Transmission Fluid
2. Exxon Torque fluid 56
3. Shell Donax TD
4. Mobil fluid 424
5. Tractelf BF 12
6. Tractelf C4 - 1000
7. Hydro Clear Power Train Fluid
Other brands may be used if they meet all the specifications
and performance levels of the above.
Chassis Lubricant (CL)
Use good grade of grease designed for pin and bushings on
agricultural equipment. Lithium or aluminum complex type
grease with high viscosity base oil, tackiness and
molybdenum disulphide are suitable. Grease approved for
the NLGI certification mark GC-LB are recommended.
Grease must be SAE Multipurpose High Temperature Grease
with Extreme Pressure (EP) performance and capable of
operating at assembly temperatures above 150°C (302°F)
Depending upon the expected ambient temperature range
during the service interval, use grease as shown on the Oil
Specifications Chart.
Front Axle
Use gear oil complying to API GL5, MIL-L-2105D
specifications. Please refer Oil Specifications Chart for oil
viscosity grade at different range of ambient temperatures.
Following oils are recommended,
1. Chevron RPM Universal Gear Lubricant SAE 80W90
2. Texaco Havoline Gear Oil 80W90
3. Total Transmission DA 80W90
4. Shell Spirax Heavy Duty 80W90
5. Mobilube HD Plus 80W90
Note : Universal Tractor Transmission Oil. Oil
shall meet API GL4 performance category.
Factory filled oil is Tractelf MM H3 and is subject
to change in future.
Grease Type Temperature Limits
Arctic Grease Below -30°C (-22°F )
SAE (NLGI) #0 -30°C to 10°C (-22°F to 50°F)
SAE (NLGI) #1 -20°C to 20°C (-4°F to 68°F)
SAE (NLGI) #2 14°F to 122°F (-10°C to 50°C)
* Factory filled oil is SAE80W90EP complying to
API GL5, MIL-L-2105D specifications and is
subject to change in future.
Sr. Application Capacity Anticipated minimum air temperature
No. Gallon / Quarts –40 to +88
0
F –22 to +88
0
F –4 to +122
0
F +32 to +104
0
F +50 to +122
0
F
1 Crankcase 3 Cyl. 1.58 / 6.32 SAE 15W40 SAE 15W40 SAE 15W40 SAE 15W40 SAE 15W40
4 Cyl. 2 / 8.03
2 Transmission & 10.03 / 40.12 SAE 75W UTTO SAE 80W UTTO listed above.
Hydraulics
3 Lubrication Fittings C. L. NLGI No. as recommended
4 Front Axle - 3535 1.71 / 6.84 SAE75W90EP SAE80W140EP SAE80W90EP SAE80W140EP
4035, 4535 & 5035 2.24 / 8.96 SAE80W90EP listed above for ambient temperature range - 4
0
F to 104
0
F
Oil Specifications Chart (Table A)
To Next Page
Loading...
Need help?
General
