Makita CA5000 User Manual

10 ENGLISH
5. Slowly press down the saw head fully, and check
whether the groove cutter blade does not contacts but
almost touches the workpiece. If not, stop the tool and
wait until the groove cutter blade stops completely, and
adjustthedepthbyturningthedepthadjustingknob
again.
Adjusting depth of cut
Toadjustdepthofcut,turnthedepthadjustingknob.
For deeper cut, turn it clockwise. For shallower cut, turn
it counterclockwise.
►Fig.8: 1.Depthadjustingknob
Sighting
Triangularmarkonthebaseindicatesthecenterofthe
groove cutter blade.
Whenusingwithgroovecutterblade,aligntheoutside
triangular mark with the cutting line.
Whenusingwithcircularsawblade(optionalacces-
sory), align the inside triangular mark with the cutting
line.
►Fig.9: 1. Base 2. Outside triangular mark 3. Inside
triangular mark 4. Cutting line
Switch action
CAUTION: Before plugging in the tool, always
check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-o󰀨buttonisprovided.
Tostartthetool,pushinthelock-o󰀨buttonandpullthe
switch trigger.
Release the switch trigger to stop.
►Fig.10: 1.Lock-o󰀨button2. Switch trigger
Speed adjusting dial
CAUTION: The speed adjusting dial is not for
using low speed rated blades but for obtaining a
speed which is suitable to material of workpiece.
Useonlybladeswhichareratedforatleastthemaxi-
mumnoloadspeedstatedintheSPECIFICATIONS.
CAUTION:Thespeedadjustingdialcanbe
turned only as far as 6 and back to 1. Do not force it
past 6 or 1, or the speed adjusting function may
no longer work.
Thetoolspeedcanbeadjustedbyturningtheadjusting
dial. Higher speed is obtained when the dial is turned in
the direction of number 6; lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
maydi󰀨erwiththetypeorthicknessoftheworkpiece.In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Number min
-1
1 2,200
2 2,700
3 3,800
4 4,900
5 6,000
6 6,400
►Fig.11: 1.Speedadjustingdial
Guide plate
For aligning the guide rail (optional accessory) with the
cutting line, use the guide plate.
►Fig.12: 1. Guide plate 2.Plateedge3. Cutting line
1. Set the guide plate onto the guide rail near from
thecuttingstartpoint.Theplateedgerepresentsthe
centerofthegroovecutterblade.Aligntheplateedge
with the cutting line.
2. Then,setagaintheguideplateontheguiderail
nearthecuttingendpoint.Andaligntheplateedgewith
the cutting line again.
Other features
Thetoolsequippedwithelectronicfunctionareeasyto
operate because of the following features.
Overload protector
Whentheloadonthetoolexceedsadmissiblelevels,
power to the motor is reduced to protect the motor from
overheating.Whentheloadreturnstoadmissiblelev-
els, the tool will operate as normal.
Constant speed control
Electronicspeedcontrolforobtainingconstantspeed.
Possibletogetnenish,becausetherotatingspeedis
kept constant even under load condition.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and unplugged before carrying out
any work on the tool.
Hex wrench storage
Hexwrenchisstoredonthetool.Toremovehex
wrench,justpullitout.
Toinstallhexwrench,placeitonthegripandinsertitas
far as it goes.
►Fig.13: 1. Hex wrench

Makita CA5000 Specifications

General

Brand	Makita
Model	CA5000
Category	Cutter
Language	English