Makita DC10SB User Manual

Symbols
The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.
• Indoor use only. • Read instruction manual.
• DOUBLE INSULATION • Ready to charge.
• Charging. • Charging complete.
• Delay charge (Battery cooling, or
too cold battery).
• Defective battery.
• Delay charge (Too hot or too cold
battery).
• Cooling abnormality.
• Do not short battery. • Do not destroy battery by re.
• Do not expose battery to water or
rain.
• Always recycle battery.
Specication:
Model DC10SB DC10WD
Input A.C. 120 V 50 – 60 HZ
Output D.C. 10.8 V – D.C. 12 V (max.)
Weight 0.63 kg (1.5 lbs) 0.35 kg (0.77 lbs)
• Due to our continuing program of research and development, the specications herein are subject to change without
notice.
• Specications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1.
SAVE THESE
INSTRUCTIONS
– This manual contains important safety and
operating instructions for battery charger.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. CAUTION – To reduce risk of injury, charge only
Makita type rechargeable batteries. Other types
of batteries may burst causing personal injury and
damage.
4. Non-rechargeable batteries cannot be charged with
this battery charger.
5. Use a power source with the voltage specied on the
nameplate of the charger.
6. Do not charge the battery cartridge in presence of
ammable liquids or gases.
7. Do not expose charger to rain or snow.
8. Never carry charger by cord or yank it to disconnect
from receptacle.
9.
After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever
disconnecting charger.
10.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
11. Do not operate charger with damaged cord or plug. If
the cord or plug is damaged, ask Makita authorized
service center to replace it in order to avoid a hazard.
12. Do not operate or disassemble charger if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualied
serviceman. Incorrect use or reassembly may result
in a risk of electric shock or re.
13. The battery charger is not intended for use by young
children or inrm persons without supervision.
14. Young children should be supervised to ensure that
they do not play with the battery charger.
15. Do not charge battery cartridge when room
temperature is BELOW 10°C (50°F) or ABOVE 40°C
(104°F). At the cold temperature, charging may not
start.
16. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
17. Do not allow anything to cover or clog the charger
vents.
DC10SB
DC10WD
IMPORTANT: Read Before Using.

Makita DC10SB Specifications

General

Product type	Battery
Product color	Black
Battery voltage	12 V
Battery capacity	- Ah
Battery technology	-
Brand compatibility	Makita
Maximum charging time	60 h

Weight and Dimensions

Battery width	120 mm
Battery weight	630 g

Summary

Symbols

Specification

Important Safety Instructions

Charging

Cooling System (DC10SB)

Details the cooling fan for DC10SB model, including warning lights.

Wall Mounting

Specifications

General Power Tool Safety Warnings

Provides essential safety guidelines applicable to all power tools.

Work Area Safety

Focuses on maintaining a safe environment around the power tool.

Electrical Safety

Covers crucial electrical precautions to prevent shocks and hazards.

Personal Safety

Power Tool Use and Care

Battery Tool Use and Care

Guidelines for the proper handling and maintenance of battery packs.

Service

Instructions for obtaining professional repair and maintenance for the tool.

Cordless Driver Drill Safety Warnings

Specific safety advice for operating cordless driver drills.

Important Safety Instructions for Battery Cartridge

Tips for Maintaining Maximum Battery Life

Offers advice on extending the lifespan and performance of battery cartridges.

Functional Description

Installing or Removing Battery Cartridge

Step-by-step guide for safely attaching and detaching battery packs.

Battery Protection System

Explains the tool's system to prevent overload and battery damage.

Indicating Remaining Battery Capacity

How to check the current charge level of the battery pack.

Switch Action

Details on operating the tool's trigger for power control.

Electric Brake

Information on the tool's braking mechanism for quick stops.

Lighting Up the Front Lamp

Instructions for activating and using the tool's LED work light.

Reversing Switch Action

How to change the tool's rotation direction for drilling or driving.

Speed Change

Guide on adjusting the tool's speed settings for different tasks.

Adjusting Fastening Torque

How to set the clutch for optimal torque control during screwdriving.

Assembly

Installing or Removing Driver Bit/Drill Bit

Procedure for inserting and removing bits from the drill chuck.

Installing or Removing Driver Bit/Socket Bit

Guide for attaching and detaching bits using the sleeve mechanism.

Installing Hook

Instructions for attaching the tool's hanging hook.

Installing Driver Bit Holder

Operation

Screwdriving Operation

Best practices for driving screws with the tool.

Drilling Operation

Guidance on performing drilling tasks effectively.

Using the Tool as a Hand Screwdriver

Using Holster

Maintenance

Optional Accessories

Specifications

Important Safety Instructions for Battery Cartridge

Safety guidelines specific to the battery cartridge used with the flashlight.

Installing or Removing Battery Cartridge

Steps to insert and remove the battery from the flashlight.

Maintenance

Care and upkeep procedures for the flashlight.

Safety Warnings

General Power Tool Safety Warnings

Fundamental safety rules applicable to all power tools.

Work Area Safety

Guidelines for maintaining a safe working environment.

Electrical Safety

Precautions related to electrical hazards.

Personal Safety

Measures to ensure the operator's safety during use.

Power Tool Use and Care

Battery Tool Use and Care

Specific care instructions for battery-powered tools.

Service

Information on servicing and repairs.

Important Safety Instructions for Battery Cartridge

Symbols

Explanation of symbols used in the manual.

Cordless Impact Wrench Safety Warnings

Functional Description

Installing or Removing Battery Cartridge

Procedure for installing/removing battery cartridges.

Battery Protection System

How the system protects the battery and tool.

Switch Action

How to operate the switch trigger.

Electric Brake

Details on the electric brake feature.

Lighting Up the Front Lamp

How to use the front lamp.

Reversing Switch Action

Changing the direction of rotation.

Assembly

Selecting Correct Impact Socket

Guidance on choosing the right size impact socket.

Installing or Removing Impact Socket

Steps to install and remove impact sockets.

Installing Hook

How to attach the tool's hook.

Operation

Maintenance

Optional Accessories