Makita DC10WD - User Manual

Symbols
The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.
• Indoor use only. • Read instruction manual.
• DOUBLE INSULATION • Ready to charge.
• Charging. • Charging complete.
• Delay charge (Battery cooling, or
too cold battery).
• Defective battery.
• Delay charge (Too hot or too cold
battery).
• Cooling abnormality.
• Do not short battery. • Do not destroy battery by re.
• Do not expose battery to water or
rain.
• Always recycle battery.
Specication:
Model DC10SB DC10WD
Input A.C. 120 V 50 – 60 HZ
Output D.C. 10.8 V – D.C. 12 V (max.)
Weight 0.63 kg (1.5 lbs) 0.35 kg (0.77 lbs)
• Due to our continuing program of research and development, the specications herein are subject to change without
notice.
• Specications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1.
SAVE THESE
INSTRUCTIONS
– This manual contains important safety and
operating instructions for battery charger.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. CAUTION – To reduce risk of injury, charge only
Makita type rechargeable batteries. Other types
of batteries may burst causing personal injury and
damage.
4. Non-rechargeable batteries cannot be charged with
this battery charger.
5. Use a power source with the voltage specied on the
nameplate of the charger.
6. Do not charge the battery cartridge in presence of
ammable liquids or gases.
7. Do not expose charger to rain or snow.
8. Never carry charger by cord or yank it to disconnect
from receptacle.
9.
After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever
disconnecting charger.
10.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
11. Do not operate charger with damaged cord or plug. If
the cord or plug is damaged, ask Makita authorized
service center to replace it in order to avoid a hazard.
12. Do not operate or disassemble charger if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualied
serviceman. Incorrect use or reassembly may result
in a risk of electric shock or re.
13. The battery charger is not intended for use by young
children or inrm persons without supervision.
14. Young children should be supervised to ensure that
they do not play with the battery charger.
15. Do not charge battery cartridge when room
temperature is BELOW 10°C (50°F) or ABOVE 40°C
(104°F). At the cold temperature, charging may not
start.
16. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
17. Do not allow anything to cover or clog the charger
vents.
DC10SB
DC10WD
IMPORTANT: Read Before Using.

Summary

Important Safety Instructions

Save and Read All Instructions

Specifications

Tool Model and Key Features

Details on models FD05/FD06, capacities, speed, and weight.

WT02 Wrench Details

Specifications for the WT02 impact wrench, including capacities and weight.

General Power Tool Safety Warnings

Work Area and Electrical Safety

Personal Safety Precautions

Staying alert, using PPE, and maintaining balance.

Power Tool Use and Care

Operating and Maintaining Tools

Battery Tool Use and Care

Battery Handling and Safety

Guidelines for using, charging, and storing battery packs safely.

Battery Cartridge Safety Instructions

Handling, Storage, and Warnings

Important safety rules for battery cartridges.

Tips for Maximum Battery Life

Charging and Maintenance Advice

Functional Description

Battery Installation and Protection

How to install/remove battery and an overview of the protection system.

Functional Description (Continued)

Operation Modes and Indicators

Switch, Lamp, and Reversing Action

Functional Description (Continued)

Control Functions

Explains reversing switch, speed change, and torque adjustment.

Assembly Procedures

Bit and Hook Installation

Operation Guidelines

Bit Holder and Screwdriving

Important Safety Instructions

General Luminaire and Battery Safety

Safety precautions for using the flashlight and its battery.

Battery Cartridge Safety

Handling, Storage, and Disposal

Specific safety instructions for battery cartridges.

Operational Features

Battery Life, Protection, and Lighting

Safety Warnings

General Power Tool Safety

Personal and Battery Safety

Guidelines for personal safety and battery tool usage.

Service and Safety Warnings

Tool Service and Battery Safety

Impact Wrench Safety

Operational Safety and Torque

Safety warnings for impact wrench use, including socket checks and torque.

Battery Life and Functional Description

Maintaining Battery Life

Functional Description (WT02)

Battery Handling and Protection

Installing/removing battery and overview of the protection system.

Assembly

Socket Selection and Installation

Operation

Inserting Battery and Fastening

Operation (Continued)

Torque Graphs and Factors

Makita DC10WD Specifications

General

Quantity per pack	1 pc(s)