Makita DSL801TUX2 User Manual

5 ENGLISH
3. Do not use accessories which are not speci-
cally designed and recommended by the tool
manufacturer.Justbecausetheaccessorycan
beattachedtoyourpowertool,itdoesnotassure
safe operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
theirratedspeedcanbreakandyapart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool.Incorrectlysizedaccessories
cannotbeadequatelyguardedorcontrolled.
6. Do not use a damaged accessory. Before each
use inspect the accessory such as pad for
cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of
the rotating accessory and run the power tool
at maximum no-load speed for one minute.
Damagedaccessorieswillnormallybreakapart
during this test time.
7. Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appro-
priate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.
Theeyeprotectionmustbecapableofstopping
yingdebrisgeneratedbyvariousoperations.
The dust mask or respirator must be capable of
ltratingparticlesgeneratedbyyouroperation.
Prolongedexposuretohighintensitynoisemay
cause hearing loss.
8. Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragmentsofworkpieceorofabrokenaccessory
mayyawayandcauseinjurybeyondimmediate
area of operation.
9. Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
10. Position the cord clear of the spinning acces-
sory.Ifyoulosecontrol,thecordmaybecutor
snaggedandyourhandorarmmaybepulledinto
thespinningaccessory.
11. Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessorymaygrabthesurfaceandpullthe
powertooloutofyourcontrol.
12. Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessorycouldsnagyourclothing,pullingthe
accessoryintoyourbody.
13. Do not operate the power tool near ammable
materials. Sparks could ignite these materials.
14. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
mayresultinelectrocutionorshock.
Kickback and Related Warnings
Kickbackisasuddenreactiontoapinchedorsnaggedrotat-
ingpadoranyotheraccessory.Pinchingorsnaggingcauses
rapidstallingoftherotatingaccessorywhichinturncauses
the uncontrolled power tool to be forced in the direction oppo-
siteoftheaccessory’srotationatthepointofthebinding.
Forexample,ifapadissnaggedorpinchedbytheworkpiece,
the edge of the pad that is entering into the pinch point can dig
into the surface of the material causing the pad to climb out
orkickout.Thepadmayeitherjumptowardorawayfromthe
operator,dependingondirectionofthepad’smovementatthe
pointofpinching.Padmayalsobreakundertheseconditions.
Kickbackistheresultofpowertoolmisuseand/or
incorrect operating procedures or conditions and can be
avoidedbytakingproperprecautionsasgivenbelow.
1.
Maintain a rm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque reac-
tions or kickback forces, if proper precautions are taken.
2. Never place your hand near the rotating acces-
sory.Accessorymaykickbackoveryourhand.
3. Do not position your body in the area where
power tool will move if kickback occurs.
Kickbackwillpropelthetoolindirectionopposite
tothewheel’smovementatthepointofsnagging.
4.
Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners,sharpedgesorbouncinghaveatendencytosnag
therotatingaccessoryandcauselossofcontrolorkickback.
5. Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
Safety Warnings Specic for Sanding Operations:
1.
Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when select-
ing sanding paper. Larger sanding paper extending
beyondthesandingpadpresentsalacerationhazardand
maycausesnagging,tearingofthediscorkickback.
Additional Safety Warnings:
1. Do not leave the tool running. Operate the tool
only when hand-held.
2.
Check that the workpiece is properly supported.
3. Pay attention that the pad continues to rotate
after the tool is switched o󰀨.
4.
If working place is extremely hot and humid, or
badly polluted by conductive dust, use a short-cir-
cuit breaker (30 mA) to assure operator safety.
5. Do not use the tool on any materials contain-
ing asbestos.
6. Do not use cloth work gloves during operation.
Fibersfromclothglovesmayenterthetool,which
causes tool breakage.
7. Always work in well ventilated area.
8. When placing the tool, place it on a at and
stable surface.
9.
When operating the tool, connect the tool to a
vacuum cleaner as much as possible to keep the
working area clean and prevent the operator from
inhaling particles generated by the operation.
10. Handle and store accessories with care.
SAVE THESE INSTRUCTIONS.

Makita DSL801TUX2 Specifications

General

Brand	Makita
Model	DSL801TUX2
Category	Sander
Language	English