What to do if the cutting tool on my Makita DUR189 Trimmer does not rotate?
If the cutting tool of your Makita Trimmer doesn't rotate, a foreign object, like a branch, may be jammed between the protector and the cutting tool. Remove any obstructions. If the issue continues, the drive system may be faulty, requiring repair from an authorized service center.
What to do if Makita DUR189 Trimmer cutting tool and motor cannot stop?
If the cutting tool and motor of your Makita Trimmer won't stop, this could indicate an electric or electronic malfunction. Remove the battery immediately and seek repair from an authorized service center.
Why does the motor not run on my Makita Trimmer?
If your Makita Trimmer motor isn't running, there are a few potential causes. First, ensure the battery cartridge is correctly installed. If it is, the battery might be low or faulty; try recharging it, and if that doesn't work, replace the battery. If these steps don't solve the problem, the drive system may not be functioning correctly.
Why doesn't my Makita Trimmer reach maximum RPM?
Your Makita Trimmer might not be reaching maximum RPM because the battery is installed improperly (install the battery cartridge as described in this manual) or the battery power is dropping (recharge or replace the battery).
Why won't my Makita DUR189 motor run?
If the Makita Trimmer's motor isn't running, ensure the battery cartridge is properly installed. Also, check the battery's charge level and recharge or replace it if necessary. If these steps don't resolve the issue, it could be a problem with the drive system, requiring repair by an authorized service center.
What to do if my Makita Trimmer does not reach maximum RPM?
If your Makita Trimmer isn't reaching maximum RPM, first ensure the battery is correctly installed. If the issue persists, the battery power may be low, so recharge or replace it. If problems continue, the drive system might not be working correctly, and you should seek repair from an authorized service center.
Why does my Makita DUR189 Trimmer motor stop after a little use?
If the Makita Trimmer motor stops running after a short period, it could be due to a low battery charge. Recharge or replace the battery. Another possible cause is overheating; if this is the case, stop using the tool and allow it to cool down.
What to do if my Makita Trimmer has abnormal vibration?
If your Makita Trimmer is vibrating abnormally, it could be due to several reasons. * One end of the nylon cord might be broken – tap the nylon cutting head against the ground while rotating to feed the cord. * Broken plastic blade(s) – replace them with new ones. * If these steps don't solve the vibration, the drive system may not be working correctly, and you should consult an authorized service center.
What to do if the cutting tool does not rotate on my Makita DUR189?
If the cutting tool on your Makita Trimmer won't rotate, immediately stop the machine. This could be due to a foreign object, like a branch, jammed between the protector and the cutting tool. Remove the object to resolve this. If the issue persists, it may indicate a problem with the drive system.
How to fix a Makita DUR189 that does not reach maximum RPM?
If your Makita Trimmer isn't reaching its maximum RPM, first check that the battery is installed correctly as described in the manual. Also, the battery power might be dropping, so try recharging or replacing the battery. If the issue continues, the drive system may be malfunctioning.
Detailed specifications including speed, length, weight, and dimensions.
Presents the noise pressure level and vibration emission data for the tool.
Lists compatible battery cartridges and chargers for the cordless grass trimmer.
Explains the meaning of various symbols used throughout the instruction manual.
Comprehensive safety guidelines and warnings for operating the tool safely.
Defines the tool's intended purpose and lists the necessary safety gear.
Explains the automatic shut-off system to protect the tool and battery.
Details protection mechanisms against common operational issues.
How to check the battery's remaining charge level.
Essential guidelines for safe and effective handling of the tool during use.
How to attach and adjust the shoulder harness for user comfort and control.
General| Voltage | 18V |
|---|---|
| Power Source | Battery |
| Cutting Width | 300 mm |
| Spindle Size | M8 x 1.25 LH |
| Line Diameter | 2.0 mm |
| Cutting Diameter | 30 cm |
| No Load Speed | 6000 RPM |
To Next Page
