What to do if Makita EA3502S Chainsaw engine starts, but dies immediately?
If your Makita Chainsaw starts but dies immediately, it could be due to a wrong idling adjustment, or a dirty suction head or carburetor. Adjust the idling and clean the suction head or carburetor. Also, check the tank venting and fuel line, as a defective tank venting, interrupted fuel line, defective cable or combination switch could also be the cause.
Why is my Makita EA3502S engine not starting?
There could be several reasons why your Makita Chainsaw engine isn't starting. It could be due to a malfunction in the fuel supply or compression system, or a mechanical issue. Check the ignition spark and ensure the fuel tank is full. Also, inspect the STOP switch and wiring for any faults. Other potential causes include a defective carburetor, a dirty suction head, a bent or interrupted fuel line, defective cylinder base packing ring or piston rings, or broken parts in the starter or engine. Examine the cylinder base packing and piston rings. Inspect the starter spring and the engine for broken parts.
How to fix no chain lubrication on a Makita Chainsaw?
If your Makita Chainsaw isn't lubricating the chain, the oil tank might be empty, the oil guide groove could be dirty, or the oil-pump adjusting screw may be incorrectly adjusted. Fill the oil tank, clean the oil guide groove, and adjust the oil-pump screw.
How to fix insufficient power in my Makita EA3502S Chainsaw?
If your Makita Chainsaw has insufficient power, it could be due to a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a clogged exhaust channel in the cylinder, or a clogged spark arrester screen. To resolve this, clean the air filter, adjust the carburetor, and unclog the muffler, exhaust channel, and spark arrester screen.
Why is my Makita EA3502S Chainsaw chain not running?
If the chain on your Makita Chainsaw isn't running, the chain brake might be activated. Check if the chain brake is in the 'off' position.
How to fix warm start difficulties with my Makita EA3502S Chainsaw?
If you're experiencing warm start difficulties with your Makita Chainsaw, it's likely due to an incorrect carburetor adjustment. Adjust the carburetor settings.
What to do if my Makita Chainsaw engine starts, but dies immediately?
If your Makita Chainsaw engine starts but dies immediately, the idling adjustment might be wrong, or the suction head or carburetor could be dirty. Check and adjust the idling settings and clean the suction head or carburetor. Another possibility is a defective tank vent, an interrupted fuel line, a defective cable, or a defective combination switch. Inspect the tank vent and ensure the fuel line is not interrupted.
What to do if my Makita Chainsaw has insufficient power?
If your Makita Chainsaw has insufficient power, it might be because the air filter is dirty, the carburetor adjustment is wrong, the muffler is clogged, the exhaust channel in the cylinder is clogged, or the spark arrester screen is clogged. Clean the air filter and check the carburetor adjustments.
How to fix insufficient power in Makita Saw?
If your Makita Saw has insufficient power, the cause might be a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a clogged exhaust channel in the cylinder, or a clogged spark arrester screen. Clean or replace the air filter and muffler.
Why my Makita EA3502S engine does not start?
If your Makita Chainsaw engine is not starting, begin by checking the ignition spark. Also inspect the wiring, and replace the spark plug or cap if defective. Ensure proper spark plug sealing. Adjust the combination switch and clean the carburetor if the combination switch is in Choke position, or if the carburetor is defective, or the suction head is dirty, or the fuel line is bent or interrupted. Finally, inspect the starter and engine parts, and replace defective components if the cylinder base packing ring or radial shaft packings are defective, or if the cylinder or piston rings are defective.
Details mandatory personal protective equipment (PPE) for safe chainsaw operation.
Warns about kickback hazards and provides rules to prevent them during sawing.
Step-by-step guide for installing the guide bar and saw chain onto the chainsaw body.
Describes the function, engagement, and release of the chainsaw's chain brake mechanism.
Covers fuel requirements, mixing, storage, and chain oil system operation.
Details the procedures for cold starting, warm starting, and stopping the chainsaw engine.
Provides solutions for common malfunctions and problems encountered during chainsaw operation.
To Next Page
General
