To Next PageTo Next PageHow to fix a Makita EBH252U when the cutter blade does not rotate?
If the cutter blade on your Makita Brush Cutter doesn't rotate, first, ensure that the cutter blade-tightening nut is securely tightened. Also, check for any twigs or foreign matter caught by the cutter blade or dispersion-preventing cover and remove them. If the blade still doesn't rotate, request an inspection and maintenance of the drive system.
What to do if my Makita EBH252U engine stops soon after starting?
If the engine of your Makita Brush Cutter stops soon after starting, it might not be sufficiently warmed up; perform a warm-up operation. Ensure the choke lever is set to “OPEN” once the engine is warm. A clogged fuel filter or a contaminated air cleaner can also cause this issue; clean them accordingly. For an abnormal carburetor or drive system, it is recommended to request inspection and maintenance.
Why is the cutter blade not rotating on my Makita EBH252U Brush Cutter?
If your Makita Brush Cutter blade isn't rotating, first, check if the cutter blade-tightening nut is loose and tighten it securely. Also, inspect the cutter blade and dispersion-preventing cover for any caught twigs or foreign matter and remove them. For an abnormal drive system, it is recommended to request inspection and maintenance.
What to do if the cutter blade of my Makita Brush Cutter does not rotate?
If the cutter blade on your Makita Brush Cutter isn't rotating, check for: * A loosened cutter blade-tightening nut: Tighten it securely. * Twigs caught by the cutter blade or dispersion-preventing cover: Remove any foreign matter. * Abnormal drive system: Make request for inspection and maintenance.
What to do if the cutter blade on my Makita Brush Cutter doesn't stop immediately?
If the cutter blade on your Makita Brush Cutter doesn't stop immediately, it might be due to high idling rotation, which requires adjustment. Another cause could be a detached throttle wire, which needs to be securely reattached. If neither of these solutions works, request an inspection and maintenance of the drive system.
Why does my Makita EBH252U engine stop soon after starting?
If your Makita Brush Cutter engine stops soon after starting or the engine speed does not increase, it could be due to several reasons. First, ensure you perform a sufficient warm-up operation. Also, check that the choke lever is set to “OPEN” after the engine has warmed up. Other potential causes include a clogged fuel filter or a contaminated air cleaner, both of which should be cleaned. If the issue persists, request an inspection and maintenance of the carburetor or drive system.
What causes abnormal vibrations in my Makita EBH252U?
If the main unit of your Makita Brush Cutter vibrates abnormally, it could be due to a broken, bent, or worn cutter blade, which needs replacement. Another cause might be a loosened cutter blade-tightening nut, which should be securely tightened. Also, check if the convex part of the cutter blade and cutter blade support fitting has shifted, and if so, attach it securely. If the problem continues, request an inspection and maintenance of the drive system.
What to do if my Makita EBH252U engine does not stop?
If your Makita Brush Cutter engine doesn't stop, it could be due to a detached connector, which needs to be securely attached. If the problem persists, request an inspection and maintenance of the electric system.
What causes abnormal vibration in my Makita EBH252U?
Abnormal vibration in your Makita Brush Cutter can be due to a broken, bent, or worn cutter blade, which should be replaced. Ensure the cutter blade-tightening nut is securely tightened. Check the convex part of the cutter blade and cutter blade support fitting, and attach securely if shifted. For an abnormal drive system, it is recommended to request inspection and maintenance.
Why does the cutter blade on my Makita Brush Cutter not stop immediately?
If the cutter blade on your Makita Brush Cutter doesn't stop immediately, it could be due to high idling rotation, which requires adjustment. Also, check if the throttle wire is detached and attach it securely. For an abnormal drive system, it is recommended to request inspection and maintenance.
General| Type | String trimmer |
|---|---|
| Cordless | Yes |
| Head type | Blade |
| Handle type | - |
| Engine power | 1 hp |
| Product color | Black, Blue |
| Fuel tank capacity | 0.5 L |
| Engine displacement | 24.5 cm³ |
| Cutting diameter (max) | - mm |
| Power source | Gasoline |
Weight and Dimensions| Depth | 490 mm |
|---|---|
| Width | 620 mm |
| Length | 1770 mm |
| Weight | 5700 g |
Icons indicating important instructions and safety precautions.
Guidelines for safe operation and user responsibilities.
Details required protective gear for safe operation.
Safety precautions for handling fuel.
Explanation of kickback and potential hazards.
Guidelines for routine maintenance of the equipment.
Instructions for mounting the handle on bike handle models.
Steps to mount the cutter blade using a hex wrench.
Procedure for checking and refilling engine oil.
Instructions for cleaning and using the oil gauge.
Safety precautions for handling fuel.
Guidelines for fuel storage duration.
Details about the type of fuel and usage points.
Instructions for adjusting the shoulder strap for proper balance.
Steps for starting the petrol brushcutter correctly.
Procedure to check and adjust the engine's idling speed.
How to operate the nylon cutting head effectively.
Steps for replacing the nylon cutting cord.
Daily checks and maintenance tasks to perform.
Details on warranty period and coverage for emissions control system.
Owner's duties regarding maintenance and warranty claims.
Coverage details for emission component defects.
List of emission-related parts covered by the warranty.
Importance of proper maintenance for warranty coverage.
Procedure for making a warranty claim.
