EasyManua.ls Logo

Makita EBH341U - User Manual

Makita EBH341U
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Petrol Brushcutter
EBH341U/EBH341L
Important:
Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe
the safety regulations!
Preserve instruction manual carefully!
EBH341U EBH341L
ORIGINAL INSTRUCTION MANUAL

Table of Contents

Other manuals for Makita EBH341U

Preview: Instruction Manual
Instruction Manual96 pages

Questions and Answers

  • R
    rose79Sep 8, 2025
    Why does my Makita Brush Cutter engine stop soon after starting and not reach full speed?
    • B
      Brandi RobertsSep 8, 2025
      Your Makita Brush Cutter might be stopping soon after starting, or failing to reach full speed, due to several reasons. Ensure you've warmed up the engine sufficiently. Check that the choke lever is set to “OPEN” after the engine warms up. A clogged fuel filter or a contaminated air cleaner can also cause these issues, so clean them. If these steps don't resolve the problem, the carburetor or drive system may be abnormal.
  • D
    David JohnsonAug 23, 2025
    Why won't my Makita Brush Cutter engine start?
    • M
      Michael MillerAug 23, 2025
      If the engine of your Makita Brush Cutter doesn't start, several factors could be at play. First, ensure you're operating the primer pump correctly by pushing it 7 to 10 times. Check that you are pulling the starter rope strongly enough. Verify that there is enough fuel in the tank and that the fuel filter isn't clogged. Inspect the fuel tube for any breaks and straighten it if necessary. Replace deteriorated fuel with fresh fuel, ideally every month. If there's excessive fuel suction, adjust the throttle lever from medium to high speed and pull the starter handle. Also, make sure the plug cap is securely attached and the spark plug is clean and properly gapped. If issues persist, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
  • A
    Alicia PetersonAug 25, 2025
    What to do if the cutter blade does not rotate on my Makita EBH341U?
    • O
      oramirezAug 25, 2025
      If the cutter blade on your Makita Brush Cutter isn't rotating, stop the engine immediately. Ensure the cutter blade-tightening nut is securely tightened. Also, check for any twigs or foreign matter caught by the cutter blade or dispersion-preventing cover and remove them. If the issue persists, there may be an abnormal drive system, and you should request an inspection and maintenance.
  • S
    Shawn RobertsAug 26, 2025
    Why does my Makita EBH341U Brush Cutter engine stop soon or not increase speed?
    • D
      Daniel SteeleAug 27, 2025
      If your Makita Brush Cutter's engine stops soon after starting or the engine speed doesn't increase, it could be due to several reasons. Make sure to perform a proper warm-up operation. Ensure the choke lever is set to the 'OPEN' position once the engine is warmed up. Check and clean the fuel filter if it's clogged. Also, inspect the air cleaner for contamination or clogs and clean it. If these steps don't resolve the issue, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
  • B
    Brittany GonzalezAug 27, 2025
    What causes abnormal vibration in my Makita Brush Cutter?
    • T
      Tami AndersonAug 27, 2025
      If your Makita Brush Cutter is vibrating abnormally, stop the engine immediately. Check the cutter blade for any damage such as being broken, bent, or worn, and replace it if necessary. Ensure the cutter blade-tightening nut is securely tightened. Verify that the convex part of the cutter blade and cutter blade support fitting are correctly attached. If the vibration continues, there might be an issue with the drive system, requiring professional inspection and maintenance.
  • H
    Heather FryeSep 22, 2025
    Why is my Makita EBH341U main unit vibrating abnormally?
    • A
      Anthony MorrisSep 22, 2025
      Abnormal vibration in your Makita Brush Cutter can stem from several issues: * A broken, bent, or worn cutter blade, which should be replaced. * A loosened cutter blade-tightening nut, which needs to be securely tightened. * Also, check the convex part of cutter blade and cutter blade support fitting, and attach securely if shifted. * If the problem continues, the drive system may be abnormal, requiring inspection and maintenance.
  • X
    xmoraSep 16, 2025
    What to do if my Makita Brush Cutter engine stops soon after starting?
    • E
      evan52Sep 16, 2025
      If your Makita Brush Cutter engine stops shortly after starting, consider the following: * Ensure you perform a proper warm-up operation. * Check that the choke lever is set to “OPEN” once the engine is warmed up. * A clogged fuel filter or a contaminated air cleaner can also cause this issue; clean them. * If the problem persists, it could be an issue with the carburetor or drive system, requiring professional inspection and maintenance.
  • I
    ijohnsonSep 18, 2025
    What to do if the cutter blade does not stop immediately on my Makita Brush Cutter?
    • D
      Dustin ManningSep 18, 2025
      If the cutter blade on your Makita Brush Cutter doesn't stop immediately, it could be due to: * High idling rotation, which requires adjustment. * A detached throttle wire, which needs to be securely attached. * If these steps don't resolve the issue, there may be an abnormal drive system, and it is recommended to request inspection and maintenance.
  • J
    Jessica DeanSep 7, 2025
    How to start a Makita EBH341U when the engine won't start?
    • X
      xavier64Sep 7, 2025
      If your Makita Brush Cutter's engine isn't starting, there are several potential causes. First, ensure you're operating the primer pump correctly by pushing it 7 to 10 times. Check that you're pulling the starter rope strongly enough. Make sure the fuel tank isn't empty and that the fuel filter isn't clogged—clean it if it is. Inspect the fuel tube for breaks and straighten it if necessary. If the fuel is old, replace it (recommended every month). If there's excessive fuel suction, set the throttle lever to high speed and pull the starter handle. Also, check that the plug cap is securely attached, the spark plug is clean, and the spark plug clearance is correctly adjusted. If these steps don't work, consider cleaning or replacing the spark plug.
  • J
    Joseph OrtizSep 4, 2025
    What causes the metal blade on my Makita EBH341U to not stop immediately?
    • D
      Dr. Marcus MartinSep 4, 2025
      If the metal blade on your Makita Brush Cutter doesn't stop immediately after you stop the engine, try to adjust the idling rotation. Also, make sure that the throttle wire is securely attached. If the issue persists, request professional inspection and maintenance for potential drive system problems.

Summary

SYMBOLS

SAFETY INSTRUCTIONS

General Safety Guidelines

General safety precautions and recommendations for operating the equipment safely.

Intended Use and Personal Protective Equipment

Specifies the machine's intended purpose and required personal protective gear.

Starting Up the Brushcutter

Instructions and safety checks before starting the brushcutter.

REFUELING PROCEDURES

Safe Fuel Handling

Guidelines for safely handling fuel, including precautions against inhalation and skin contact.

Fuel Storage and Deterioration

Recommendations for storing fuel to prevent deterioration and ensure safety.

Fuel Type and Points

Information on the correct fuel type and important points to consider during refueling.

METHOD OF OPERATION

General Operating Procedures

Essential guidelines for operating the brushcutter safely and effectively.

Cutting Tool Usage and Hazards

Guidance on using different cutting tools and awareness of kickback hazards.

MAINTENANCE INSTRUCTIONS

FIRST AID

EC DECLARATION OF CONFORMITY

TECHNICAL DATA

DESIGNATION OF PARTS

EBH341 U Parts Identification

Diagram and list of parts for the EBH341U model.

EBH341 L Parts Identification

Diagram and list of parts for the EBH341L model.

MOUNTING OF HANDLE

Bike Handle Mounting

Instructions for mounting the handle on bike handle models.

Loop Handle Mounting

Instructions for mounting the handle on loop handle models.

MOUNTING OF PROTECTOR

Metal Blade Protector Installation

Steps for installing the protector for metal blades.

Nylon Cutting Head Protector Installation

Steps for installing the protector for nylon cutting heads.

MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD

Mounting the Cutter Blade

Procedure for attaching the cutter blade to the brushcutter.

Mounting the Nylon Cutting Head

Procedure for attaching the nylon cutting head.

BEFORE START OF OPERATION

Engine Oil Inspection and Refill

How to check and refill the engine oil correctly.

Handling Spilled Engine Oil

Instructions for cleaning up spilled engine oil to prevent contamination.

FUEL MANAGEMENT AND SAFETY

Fuel Handling Precautions

Safety measures for handling fuel, including ventilation and avoiding contact.

Fuel Storage Guidelines

Recommendations for storing fuel to maintain quality and safety.

Refueling Process

Step-by-step guide for safely refueling the brushcutter.

CORRECT HANDLING OF MACHINE

Shoulder Strap Attachment and Detachment

Instructions for attaching and detaching the shoulder strap for proper use.

OPERATION AND STOPPING PROCEDURES

Brushcutter Starting Procedure (Cold Start)

Detailed steps for starting the brushcutter from a cold state.

BRUSHCUTTER OPERATION DETAILS

Primer, Recoil, and Choke Operation

Guide to using the primer, recoil starter, and choke lever for engine start.

Warm-up and Post-Startup Procedures

Instructions for warming up the engine and starting after a brief stop.

Stopping the Brushcutter

Steps and precautions for safely stopping the brushcutter engine.

THROTTLE AND SPEED ADJUSTMENT

Throttle Lever Operation

How to operate the throttle lever for engine speed control.

Engine Speed and Idling Adjustment

Procedures for adjusting engine rotation and low-speed idling.

CUTTING TOOL MAINTENANCE

Cutter Blade Resharpening

Information on resharpening and maintaining cutter blades.

Nylon Cutting Head Operation

Guidance on operating and feeding nylon cord in the cutting head.

REPLACING THE NYLON CORD

SERVICING INSTRUCTIONS

Daily Checkup and Maintenance

Regular checks and cleaning tasks to perform daily.

Engine Oil Replacement

Instructions and schedule for replacing engine oil.

ENGINE OIL REPLACEMENT PROCEDURE

OIL HANDLING AND DISPOSAL

AIR CLEANER MAINTENANCE

SPARK PLUG CHECK

GEAR CASE LUBRICATION

FUEL FILTER MAINTENANCE

FUEL PIPE REPLACEMENT

BOLT, NUT, AND SCREW INSPECTION

PARTS CLEANING AND REPLACEMENT

STORAGE GUIDELINES

Preparing for Long-Term Storage

Steps for preparing the brushcutter for extended storage periods.

Post-Storage Checks

Checks to perform before restarting the brushcutter after long-term storage.

MAINTENANCE SCHEDULE

TROUBLESHOOTING GUIDE

Engine Start, Stoppage, and Speed Issues

Addresses common problems related to engine starting, stopping, and speed.

Performance and Control Problems

Troubleshooting steps for issues with performance and machine control.

Vibration and Blade Issues

Diagnosing and resolving problems related to vibration and cutting blade.

Makita EBH341U Specifications

General IconGeneral
Power sourceGasoline
CordlessYes
Line diameter25.4 mm
Product colorBlack, Cyan
Rotational speed10000 RPM
Cutting diameter (max)- mm
Weight and Dimensions IconWeight and Dimensions
Weight7100 g

Related product manuals