What should I do if the metal blade on my Makita EBH341U Brush Cutter does not rotate?
If the metal blade on your Makita Brush Cutter isn't rotating, first, ensure the metal blade-tightening nut is securely tightened. Also, check for any twigs or foreign matter caught by the metal blade or dispersion-preventing cover and remove them. If the issue persists, request professional inspection and maintenance for potential drive system problems.
What to do if my Makita EBH341U engine stops soon after starting or lacks power?
If your Makita Brush Cutter engine stops shortly after starting or the engine speed doesn't increase, it might not be sufficiently warmed up; perform the warm-up operation. Check that the choke lever is set to “OPEN” after the engine warms up. A clogged fuel filter or air cleaner can also cause these issues, so clean them. For abnormal carburetor or drive system issues, request professional inspection and maintenance.
What to do if my Makita Brush Cutter engine does not stop?
If your Makita Brush Cutter engine won't stop, check for a detached connector and ensure it is securely attached. If the problem persists, there may be an issue with the electric system, requiring professional inspection and maintenance.
How to fix a Makita EBH341U when the blade won't stop immediately?
If the cutter blade on your Makita Brush Cutter doesn't stop immediately after you stop the engine, it could be due to high idling rotation, which requires adjustment. Another possible cause is a detached throttle wire, which needs to be securely reattached. If neither of these fixes the issue, the drive system may be abnormal, requiring professional inspection and maintenance.
What causes abnormal vibration in my Makita Brush Cutter?
If your Makita Brush Cutter is vibrating abnormally, stop the engine immediately. Check the cutter blade for any damage such as being broken, bent, or worn, and replace it if necessary. Ensure the cutter blade-tightening nut is securely tightened. Verify that the convex part of the cutter blade and cutter blade support fitting are correctly attached. If the vibration continues, there might be an issue with the drive system, requiring professional inspection and maintenance.
Why does my Makita EBH341U Brush Cutter engine stop soon or not increase speed?
If your Makita Brush Cutter's engine stops soon after starting or the engine speed doesn't increase, it could be due to several reasons. Make sure to perform a proper warm-up operation. Ensure the choke lever is set to the 'OPEN' position once the engine is warmed up. Check and clean the fuel filter if it's clogged. Also, inspect the air cleaner for contamination or clogs and clean it. If these steps don't resolve the issue, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
What to do if the cutter blade does not rotate on my Makita EBH341U?
If the cutter blade on your Makita Brush Cutter isn't rotating, stop the engine immediately. Ensure the cutter blade-tightening nut is securely tightened. Also, check for any twigs or foreign matter caught by the cutter blade or dispersion-preventing cover and remove them. If the issue persists, there may be an abnormal drive system, and you should request an inspection and maintenance.
Why won't my Makita Brush Cutter engine start?
If the engine of your Makita Brush Cutter doesn't start, several factors could be at play. First, ensure you're operating the primer pump correctly by pushing it 7 to 10 times. Check that you are pulling the starter rope strongly enough. Verify that there is enough fuel in the tank and that the fuel filter isn't clogged. Inspect the fuel tube for any breaks and straighten it if necessary. Replace deteriorated fuel with fresh fuel, ideally every month. If there's excessive fuel suction, adjust the throttle lever from medium to high speed and pull the starter handle. Also, make sure the plug cap is securely attached and the spark plug is clean and properly gapped. If issues persist, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
General| Power source | Gasoline |
|---|---|
| Cordless | Yes |
| Line diameter | 25.4 mm |
| Product color | Black, Cyan |
| Rotational speed | 10000 RPM |
| Cutting diameter (max) | - mm |
Weight and Dimensions| Weight | 7100 g |
|---|
General safety precautions and recommendations for operating the equipment safely.
Specifies the machine's intended purpose and required personal protective gear.
Instructions and safety checks before starting the brushcutter.
Guidelines for safely handling fuel, including precautions against inhalation and skin contact.
Recommendations for storing fuel to prevent deterioration and ensure safety.
Information on the correct fuel type and important points to consider during refueling.
Essential guidelines for operating the brushcutter safely and effectively.
Guidance on using different cutting tools and awareness of kickback hazards.
Diagram and list of parts for the EBH341U model.
Diagram and list of parts for the EBH341L model.
Instructions for mounting the handle on bike handle models.
Instructions for mounting the handle on loop handle models.
Steps for installing the protector for metal blades.
Steps for installing the protector for nylon cutting heads.
Procedure for attaching the cutter blade to the brushcutter.
Procedure for attaching the nylon cutting head.
How to check and refill the engine oil correctly.
Instructions for cleaning up spilled engine oil to prevent contamination.
Safety measures for handling fuel, including ventilation and avoiding contact.
Recommendations for storing fuel to maintain quality and safety.
Step-by-step guide for safely refueling the brushcutter.
Instructions for attaching and detaching the shoulder strap for proper use.
Detailed steps for starting the brushcutter from a cold state.
Guide to using the primer, recoil starter, and choke lever for engine start.
Instructions for warming up the engine and starting after a brief stop.
Steps and precautions for safely stopping the brushcutter engine.
How to operate the throttle lever for engine speed control.
Procedures for adjusting engine rotation and low-speed idling.
Information on resharpening and maintaining cutter blades.
Guidance on operating and feeding nylon cord in the cutting head.
Regular checks and cleaning tasks to perform daily.
Instructions and schedule for replacing engine oil.
Steps for preparing the brushcutter for extended storage periods.
Checks to perform before restarting the brushcutter after long-term storage.
Addresses common problems related to engine starting, stopping, and speed.
Troubleshooting steps for issues with performance and machine control.
Diagnosing and resolving problems related to vibration and cutting blade.
To Next Page
