Makita EM4350LH - User Manual

Other manuals for Makita EM4350LH

Questions and Answers

T
Tasha DuranNov 21, 2025
Why won't my Makita Trimmer engine start?
- K
  Kristine JohnsonNov 21, 2025
  If your Makita Trimmer's engine won't start, several factors could be the cause. First, ensure the I-O switch is set to OPERATION. Check the fuel level and replenish if necessary. A clogged fuel filter can also prevent starting, so clean it. Inspect the fuel tube for breaks and straighten if needed. If the fuel is old, replace it, as deteriorated fuel makes starting difficult (replace every month). Also, make sure the plug cap is securely attached and the spark plug is clean and properly gapped. If there was excessive suction of fuel, set throttle lever from medium speed to high speed, and pull starter handle until engine starts. Once engine starts, metal blade starts rotating, so pay full attention to metal blade. If engine will not start still, remove spark plug, dry the electrode, and r...
S
Sarah DudleyAug 25, 2025
What to do if the metal blade on my Makita Trimmer does not stop immediately?
- D
  Dr. Alec SullivanAug 26, 2025
  If the metal blade on your Makita Trimmer doesn't stop immediately, the high idling rotation may be the issue, so adjust it. Check if the throttle wire is detached and attach it securely. For abnormal drive system, it is best to request inspection and maintenance.
K
Kristin OdomAug 27, 2025
What to do if the metal blade on my Makita Brush Cutter does not rotate?
- C
  Candice PowersAug 27, 2025
  If the metal blade on your Makita Brush Cutter isn't rotating, check for a loosened metal blade-tightening nut and tighten it securely. Also, inspect the blade and dispersion-preventing cover for any caught twigs or foreign matter and remove them.
D
Drew FrancisAug 27, 2025
What to do if the metal blade on my Makita EM4350LH Brush Cutter does not stop immediately?
- P
  patriciathompsonAug 27, 2025
  If the metal blade on your Makita Brush Cutter doesn't stop immediately, the high idling rotation may need adjustment. Also, check whether the throttle wire is detached and attach it securely if needed.
V
Vanessa RuizAug 28, 2025
What to do if metal blade does not rotate on Makita Trimmer?
- P
  Pamela CrawfordAug 28, 2025
  If the metal blade on your Makita Trimmer isn't rotating, check these items: * The metal blade-tightening nut may be loosened; tighten it securely. * Twigs might be caught by the metal blade or dispersion-preventing cover; remove any foreign matter. * The drive system may be abnormal; make a request for inspection and maintenance.
M
Mary HernandezSep 16, 2025
Why won't my Makita Trimmer engine stop?
- J
  James MuellerSep 16, 2025
  If the engine of your Makita Trimmer does not stop, it might be due to: * A detached connector; attach it securely. * An abnormal electric system; make a request for inspection and maintenance.
D
David ThomasSep 14, 2025
What to do if Makita Trimmer engine stops soon after starting?
- J
  John BaileySep 14, 2025
  If your Makita Trimmer's engine stops soon after starting, consider the following possibilities: * The engine might not be sufficiently warmed up; perform a warm-up operation. * The choke lever may be set to “CLOSE” although the engine is warmed up; set it to “OPEN”. * The fuel filter could be clogged; clean it. * The air cleaner might be contaminated or clogged; clean it. * The carburetor may be abnormal; make a request for inspection and maintenance. * The drive system may be abnormal; make a request for inspection and maintenance.
L
Lonnie BurnsSep 15, 2025
Why does my Makita Trimmer main unit vibrate abnormally?
- A
  ashley34Sep 15, 2025
  Abnormal vibration in your Makita Trimmer can stem from: * A broken, bent, or worn metal blade; replace the metal blade. * A loosened metal blade-tightening nut; tighten it securely. * A shifted convex part of the metal blade and metal blade support fitting; attach securely. * An abnormal drive system; make a request for inspection and maintenance.
J
Jeffrey DominguezSep 6, 2025
Why does my Makita EM4350LH Brush Cutter main unit vibrate abnormally?
- H
  hensleysusanSep 6, 2025
  Abnormal vibration in your Makita Brush Cutter can be caused by a broken, bent, or worn metal blade (replace the metal blade); a loosened metal blade-tightening nut (tighten securely); or a shifted convex part of metal blade and metal blade support fitting (attach securely).
M
Megan JohnsonSep 4, 2025
Why won't my Makita Brush Cutter engine start?
- J
  Jose DeanSep 4, 2025
  The engine of your Makita Brush Cutter might not be starting due to several reasons: the I-O switch is set to STOP (set it to OPERATION); failure to operate primer pump (push 7 to 10 times); low pulling speed of starter rope (pull strongly); lack of fuel (feed fuel); clogged fuel filter (clean it); broken fuel tube (straighten fuel tube); deteriorated fuel (replace with new fuel, recommended every month); excessive suction of fuel (set throttle lever from medium speed to high speed, and pull starter handle until engine starts); detached plug cap (attach securely); contaminated spark plug (clean); abnormal clearance of spark plug (adjust clearance); other abnormality of spark plug (replace).