EasyManua.ls Logo

Makita EM401MP - User Manual

Makita EM401MP
84 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
EM400MP
EM401MP
Original Instruction Manual
Instructions d’emploi d’origine
Originalbetriebsanleitung
Manuale di istruzioni originale
Originele gebruiksaanwijzing
Instrucciones de manejo originales
Instruções de serviço original
Original brugsanvisning
Πρωτότυπο εγχειρίδιο οδηγιών
Orijinal Kullanım Kılavuzu
WARNING: Before use, read this booklet and the instruction manual of the power unit. Failure to follow the warnings and instructions may
cause serious or fatal injury.
AVERTISSEMENT : Avant d’utiliser l’outil, lisez la présente brochure et le manuel d’instructions du groupe moteur. Le non-respect des mises
en garde et instructions peut entraîner des blessures graves, voire mortelles.
WARNUNG: Lesen Sie vor Verwendung des Aufsatzes diese Broschüre und die Betriebsanleitung des Antriebs. Bei Nichtbeachten dieser
Warnungen und Anweisungen kann es zu schweren oder gar tödlichen Verletzungen kommen.
AVVERTENZA: Leggere il presente opuscolo e le istruzioni del gruppo di alimentazione prima dell’uso. La mancata osservanza delle
avvertenze e delle istruzioni può condurre a infortuni gravi o letali.
WAARSCHUWING: Lees voor gebruik deze gebruiksaanwijzing en de gebruiksaanwijzing van uw multifunctionele aandrijfsysteem
aandachtig door. Het niet volgen van de waarschuwingen en instructies kan leiden tot ernstig of fataal letsel.
ADVERTENCIA: Antes del uso, lea este folleto y el manual de instrucciones del grupo motor. Si no se siguen las advertencias y las
instrucciones, se pueden provocar lesiones graves o fatales.
AVISO: Antes da utilização, leia este folheto e o manual de instruções da unidade de alimentação. O não cumprimento dos avisos e
instruções pode causar ferimentos graves ou fatais.
ADVARSEL: Læs dette hæfte og brugsanvisningen til drivenheden inden brug. Det kan medføre alvorlig eller dødelig tilskadekomst, hvis du
ikke overholder advarslerne og følger instruktionerne.
ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Πριν από τη χρήση, παρακαλούμε διαβάστε αυτό το φυλλάδιο και το εγχειρίδιο οδηγιών της κινητήριας μονάδας. Η
παράλειψη εφαρμογής των προειδοποιήσεων και των οδηγιών μπορεί να προκαλέσει σοβαρό ή θανατηφόρο τραυματισμό.
UYARI: Kullanmaya başlamadan önce, bu kılavuzu ve güç başlığının kullanım kılavuzunu okuyun. Verilen uyarılara ve talimatlara
uyulmaması ciddi ve hatta ölümcül yaralanmalara yol açabilir.

Table of Contents

Other manuals for Makita EM401MP

Preview: Owner's Manual
Owner's Manual32 pages

Questions and Answers

  • H
    helen56Aug 9, 2025
    What to do if my Makita EM401MP vibrates abnormally?
    • S
      sbrownAug 9, 2025
      If your Makita Brush Cutter vibrates abnormally, it could be due to several reasons. The cutting tool might be bent, worn, or broken, in which case, replace it with a new one. Ensure the cutting tool is securely tightened. If using a nylon cutting head, check if one end of the nylon cutting cord is broken, causing imbalance; feed the cord by tapping the head on the ground. Also, verify that the cutting blade is correctly fitted on the guide of the receive washer, and install it properly if needed. If the drive system isn't working correctly, it needs inspection and repair by a Makita authorized service center.
  • T
    Timothy ValenciaAug 14, 2025
    Why is the cutting tool not rotating on my Makita EM401MP?
    • K
      Kimberly HayesAug 14, 2025
      If the cutting tool on your Makita Brush Cutter isn't rotating, make sure it's tightened securely. Also, check for any obstructions like twigs caught between the cutting tool and the protector, and remove them. If the issue persists, the drive system may not be functioning correctly, requiring inspection and repair by a Makita authorized service center.
  • G
    gonzalezseanAug 20, 2025
    How to fix a Makita EM401MP Brush Cutter when the nylon cutting cord does not feed?
    • S
      steven43Aug 21, 2025
      If the nylon cutting cord on your Makita Brush Cutter doesn't feed, it may be used up or tangled in the spool. Rewind the cord to resolve this.
  • J
    jayalaAug 27, 2025
    What to do if the cutting tool does not stop on my Makita EM401MP Brush Cutter?
    • A
      Angel CastroAug 27, 2025
      If the cutting tool on your Makita Brush Cutter doesn't stop, refer to the instruction manual of the power unit, as the power unit may not be working properly.
  • T
    Travis HarrisonSep 2, 2025
    Why is the nylon cutting cord not cut off at the correct length on my Makita EM401MP?
    • H
      hartmantanyaSep 2, 2025
      If the nylon cutting cord isn't cut off at the correct length on your Makita Brush Cutter, rewind the cord if it extends past the protector. If the cord cutter on the protector is damaged or missing, ask Makita authorized service center to replace it.

Summary

Approved Power Unit

Safety Precautions

General Precautions

Personal Protective Equipment

Essential gear for operator safety.

Work Area Safety

Putting into Operation

Starting Motor

Maintenance

Assembly and Adjustment

Installing the Protector

Removing and Installing a Cutter Blade

Removing and Installing a Nylon Cutting Head

Installing Plastic Blade

Operation

Adjusting the Hanger Position and Shoulder Harness

Resharpening the Cutting Tool

Replacing the Nylon Cord

Replacing the Plastic Blade

Lubricating Moving Parts

Overall Inspection

Maintenance Schedule

Troubleshooting

Technical Data

Makita EM401MP Specifications

General IconGeneral
Engine Displacement40.2 cc
Engine Type2-Stroke
Fuel Tank Capacity0.65 L
Shaft TypeStraight
Fuel TypeGasoline

Related product manuals