EasyManua.ls Logo

Makita ER400MP - User Manual

Makita ER400MP
64 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Original Instruction Manual
Instructions d’emploi d’origine
Originalbetriebsanleitung
Manuale di istruzioni originale
Originele gebruiksaanwijzing
Instrucciones de manejo originales
Instruções de serviço original
Original brugsanvisning


ER400MP
Warning: Before use, read this booklet and the instruction manual of the power unit. Failure to follow the
warnings and instructions may cause serious or fatal injury.
Avertissement : Avant d’utiliser l’outil, lisez la présente brochure et le mode d’emploi du groupe moteur. Le
non-respect des instructions et des mises en garde peut entraîner des blessures graves ou mortelles.
Warnung: Lesen Sie vor Verwendung des Kettensägenaufsatzes diese Broschüre und die Betriebsanleitung
des Antriebs. Bei Nichtbeachten dieser Warnungen und Anweisungen kann es zu schweren oder gar tödlichen
Verletzungen kommen.
Avvertenza: Prima dell’uso è opportuno leggere il presente opuscolo e il manuale di istruzioni del gruppo di
alimentazione. La mancata osservanza delle avvertenze e delle istruzioni può condurre a infortuni gravi o letali.
Waarschuwing: Lees voor gebruik deze gebruiksaanwijzing en de gebruiksaanwijzing van uw
multifunctionele aandrijfsysteem aandachtig door. Het niet volgen van de waarschuwingen en instructies kan
leiden tot ernstig of fataal letsel.
Advertencia: Antes del uso, lea este folleto y el manual de instrucciones del grupo motor. Si no se respetan
las advertencias y las instrucciones, se pueden producir lesiones graves o fatales.
Aviso: Antes da utilização, leia este folheto e o manual de instruções da unidade de alimentação. O
incumprimento dos avisos e instruções pode causar ferimentos graves ou fatais.
Advarsel: Læs dette hæfte og brugsanvisningen til drivenheden inden brug. Manglende overholdelse af
advarslerne og instruktionerne kan medføre alvorlig eller dødelige tilskadekomst.






Table of Contents

Other manuals for Makita ER400MP

Questions and Answers

  • L
    Larry PetersonJul 28, 2025
    Why is the cutting attachment on my Makita Trimmer not rotating?
    • L
      Leah MullenJul 28, 2025
      If the cutting attachment on your Makita Trimmer doesn't rotate, stop the engine right away. Here's what might be happening: * The cutting attachment might not be tightened securely. Make sure to tighten it properly. * There could be a twig or other foreign object caught between the cutting attachment and the protector. Remove any debris you find. * If neither of these fixes the issue, the drive system may not be working correctly. In this case, you should have it inspected and repaired by a Makita authorized service center.
  • J
    Joanne HillAug 4, 2025
    How to fix a Makita Trimmer when the nylon cutting cord does not feed?
    • K
      Krystal WilliamsAug 4, 2025
      If the nylon cutting cord on your Makita Trimmer isn't feeding, it might be used up or tangled in the spool. Try rewinding the cord to resolve this issue.
  • A
    Amanda GlassAug 12, 2025
    Why is the nylon cutting cord on my Makita Trimmer not cut off at the correct length?
    • J
      Jonathan JohnsonAug 12, 2025
      If the nylon cutting cord on your Makita Trimmer isn't being cut off at the correct length, it could be due to the following reasons: * The cord cutter on the protector might be damaged or missing. If this is the case, you should ask a Makita authorized service center to replace the cord cutter. * The cord might be extending past the protector. Try rewinding the cord.
  • T
    Thomas GravesAug 19, 2025
    What to do if my Makita Trimmer vibrates abnormally?
    • K
      Kayla RodriguezAug 20, 2025
      If your Makita Trimmer is vibrating abnormally, stop using it immediately. This could be due to several reasons: * The cutting attachment might be broken, in which case you should replace it. * The cutting attachment might not be tightened securely; ensure it is properly tightened. * If you're using a nylon cutting cord, one end might be broken, causing the head to become unbalanced. Try feeding the nylon cutting cord by tapping the head on the ground. * If none of these steps resolve the issue, the drive system may not be working correctly. Contact an authorized Makita service center for inspection and repair.

Summary

Approved Power Unit

Part Description

Safety Precautions

Personal Protective Equipment

Essential safety gear like helmets, goggles, gloves, and ear protection for safe operation.

Work Area Safety

Safe operation environment, visibility, ventilation, footing, and keeping bystanders away.

Putting into Operation

Starting Engine

Instructions on safely starting the engine, including PPE and location.

Operation

Guidance on operating the string trimmer safely, handling emergencies, and proper grip.

Assembly and Adjustment

Mounting the Protector

Instructions for installing the protector to guard against thrown debris.

Mounting the Attachment to a Power Unit

Steps to securely attach the string trimmer to the power unit.

Mounting a Nylon Cutting Head

Guide on how to properly install the nylon cutting head.

Feeding the Nylon Cutting Cord

Rewinding the Nylon Cutting Cord

Lubricating Moving Parts

Overall Inspection

Maintenance Schedule

Troubleshooting

Technical Data

EC Declaration of Conformity

Makita ER400MP Specifications

General IconGeneral
BrandMakita
ModelER400MP
CategoryGarden Machinery Accessories
LanguageEnglish

Related product manuals