EasyManuals Logo

Makita HM1111C User Manual

Makita HM1111C
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
2 ENGLISH
SPECIFICATIONS
Model HM1111C HM1101C
Blows per minute 1,100 - 2,650 min
-1
Overall length 528 mm 528 mm
Net weight with D-shaped side handle 8.0 kg 7.3 kg
Net weight with side grip 7.8 kg 7.2 kg
Safety class
II
• Due to our continuing programme of research and development, the specications herein are subject to change
without notice.
• Specications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
DOUBLE INSULATION
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for chiselling work in concrete,
brick, stone and asphalt as well as for driving and com-
pacting with appropriate accessories.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Model HM1111C
Sound pressure level (L
pA
) : 88 dB (A)
Sound power level (L
WA
) : 99 dB (A)
Uncertainty (K) : 3 dB (A)
Model HM1101C
Sound pressure level (L
pA
) : 90 dB (A)
Sound power level (L
WA
) : 101 dB (A)
Uncertainty (K) : 3 dB (A)
NOTE:
The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared noise emission value(s) may also
be used in a preliminary assessment of exposure.
WARNING: Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Model HM1111C
Work mode : chiselling function with side handle
Vibration emission (a
h,CHeq
) : 7.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode : chiselling function with side grip
Vibration emission (a
h,CHeq
) : 8.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model HM1101C
Work mode : chiselling function with side handle
Vibration emission (a
h,CHeq
) : 13.5 m/s
2
Uncertainty (K) : 2.0 m/s
2
Work mode : chiselling function with side grip
Vibration emission (a
h,CHeq
) : 13.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING: The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Makita HM1111C and is the answer not in the manual?

Makita HM1111C Specifications

General IconGeneral
Input power1300 W
Impact energy (max)11.2 J
Vibration level (chiseling)7.5 m/s²
Toolholder18 mm
Impact rate2650 bpm
Product colorBlack, Blue
Weight and Dimensions IconWeight and Dimensions
Depth126 mm
Width528 mm
Height247 mm
Weight8000 g

Related product manuals