Manitou MLT625-75 H S1-E3 - Page 105

3-3-1919
- Swivel the alternator assembly so as to obtain the belt tension required.- Swivel the alternator assembly so as to obtain the belt tension required.
- Retighten screws 1 (- Retighten screws 1 (fig. C1) (tightefig. C1) (tightening torque 22ning torque 22 N.m)N.m)
16.2 lbf/ft16.2 lbf/ft
..
If the compressor belt has to be changed, check the tension again after the first 20 If the compressor belt has to be changed, check the tension again after the first 20 hours of operation.hours of operation.
C2 - COMPRESSOR BELT TENSION (OPTION AIR CONDITIONING)C2 - COMPRESSOR BELT TENSION (OPTION AIR CONDITIONING)
CHECK - ADJUSTCHECK - ADJUST
- Open the I.C. engine bonnet.- Open the I.C. engine bonnet.
-- Check the belt for siCheck the belt for signs of wear and cracks and gns of wear and cracks and change if necessary (see: 3 - MAINTENAchange if necessary (see: 3 - MAINTENANCE:NCE:
FILTERS CARTRIDGES AND BELTS).FILTERS CARTRIDGES AND BELTS).
- Check the belt tension between the pulley of the crankshaft and of - Check the belt tension between the pulley of the crankshaft and of the compressor.the compressor.
-- Under a normal Under a normal pressure exerted with the thumb pressure exerted with the thumb (45(45 N), the belN), the belt should mt should move approximatelyove approximately
1100 mmmm(.39 in)(.39 in)..
- Carry out adjustments if necessary.- Carry out adjustments if necessary.
- Untighten screw 1 and nuts 2 - Untighten screw 1 and nuts 2 (fig. C2) by two to three thread (fig. C2) by two to three thread turns.turns.
- Swivel the alternator assembly so as to obtain the belt tension required.- Swivel the alternator assembly so as to obtain the belt tension required.
- Retighten screw 1 and - Retighten screw 1 and nuts 2 (fig. C2) nuts 2 (fig. C2) (tightening torque 22(tightening torque 22 N.m)N.m)16.2 lbf/ft16.2 lbf/ft..
If the compressor belt has to be changed, check the tension again after the first 20 If the compressor belt has to be changed, check the tension again after the first 20 hours of operation.hours of operation.
C3 - FUEL WATER TRAPC3 - FUEL WATER TRAP
DRAINDRAIN
The water trap serves to stop the water contained in the fuel, it is incorporatedThe water trap serves to stop the water contained in the fuel, it is incorporated within thewithin the
fuel filter.fuel filter.
- Open the I.C. engine bonnet.- Open the I.C. engine bonnet.
-- Place a receptacPlace a receptacle under drain le under drain porport 1 (fig. t 1 (fig. C3).C3).
-- Unscrew ring 2 (fig. C3) by two or tUnscrew ring 2 (fig. C3) by two or three thread turns to drain the water from the waterhree thread turns to drain the water from the water
trap.trap.
- Retighten ring 2 (fig. C3).- Retighten ring 2 (fig. C3).
C4 - CAB VENTILATION FILTERC4 - CAB VENTILATION FILTER
CHANGECHANGE
-- Lift out cab ventilation filLift out cab ventilation filter 1 (fig. C4) and replace it with a new one (seeter 1 (fig. C4) and replace it with a new one (see: 3 - MAINTENANCE:: 3 - MAINTENANCE:
FILTERS AND BELTS).FILTERS AND BELTS).
C2C2
11
22
22
C4C4
11
C3C3
22
11

C5 - TRANSFER BOX OIL LEVEL
C5 - TRANSFER BOX OIL LEVEL
CHECKCHECK
Place the lift truck on level ground Place the lift truck on level ground with the I.C. engine stopped.with the I.C. engine stopped.
- Remove the access panel 1 (fig. C5/1).- Remove the access panel 1 (fig. C5/1).
-- Remove level plug 2 (fig. CRemove level plug 2 (fig. C5/2). The oil should be flus5/2). The oil should be flush with the edge ofh with the edge of
the hole.the hole.
-- If necessary, add oil (see: 3 - MAINTENAIf necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS ANCE: LUBRICANTS AND FUEL) byND FUEL) by
the same hole.the same hole.
-- Replace and tighten the Replace and tighten the level plug 2 (fig. Clevel plug 2 (fig. C5/2) (tightening torque 34 to5/2) (tightening torque 34 to
4949 N.N.m)m)
25 - 36 lbf/ft25 - 36 lbf/ft
..
- Refit access panel 1 - Refit access panel 1 (fig. C5/1).(fig. C5/1).
C5/2C5/2
C5/1C5/1
11
https://www.forkliftpdfmanuals.com/