What to do if I cannot get programmed station when the PRESET button is pressed on my Marantz AV8003?
If you cannot get programmed station when the PRESET button is pressed on your Marantz Amplifier, the preset data may have been erased. Disconnecting the power plug for long periods of time will erase preset data. If that happens, input the preset data again.
How to fix Marantz Amplifier remote controller if it fails to control the unit?
If the remote controller is not working with your Marantz Amplifier, consider these potential causes: * The batteries may be depleted. Replace all batteries with new ones. * The remote controller mode might be incorrect. Switch the remote controller to the correct mode for the component you're controlling. * The distance between the unit and the remote may be too far. Move closer to the unit. * There might be an obstruction blocking the signal. Remove any objects blocking the path between the unit and the remote.
How to troubleshoot no audio output from the center channel speaker on Marantz AV8003?
If there is no audio output from the center channel speaker of your Marantz Amplifier, check the following: * Ensure the power amp and speakers are correctly connected by referring to the connection diagram. * If 'STEREO' is selected for Surround mode, no sound will be output from the center speaker. Set another Surround mode. * Verify that 'Center = NONE' has not been selected in SETUP mode. If so, make the correct setting.
How to troubleshoot no audio output from the surround speakers on Marantz AV8003?
If you are experiencing no audio output from the surround speakers on your Marantz Amplifier, consider these possibilities: * Check that the power amp and speakers are connected correctly, referring to the connection diagram. * If 'STEREO' is selected for Surround mode, no sound will be output from the surround speaker. Set another Surround mode. * Ensure that 'Surround = NONE' has not been selected in SETUP mode. Make the correct setting if needed.
How to troubleshoot no audio output from the surround back speakers on Marantz AV8003 Amplifier?
If there is no audio output from the surround back speakers on your Marantz Amplifier, consider the following: * Ensure the power amp and speakers are connected correctly, referring to the connection diagram. * The surround mode may not be EX/ES mode. Set surround mode to EX/ES. * Verify that 'Surround back = NONE' has not been selected in SPEAKERS SIZE SETUP. Make the correct setting if needed.
What does “SUB_UPDT” displayed on my Marantz AV8003 Amplifier mean?
If “SUB_UPDT” is displayed on your Marantz Amplifier, it means that the unit is updating its subscription. Wait until the encryption code has been updated.
What does “TUNER ERR” displayed on my Marantz AV8003 Amplifier mean?
If “TUNER ERR” is displayed on your Marantz Amplifier, it means that the SIRIUS Connect tuner is not properly connected. Check the 8pin mini DIN cable and AC adapter connection are correct.
What does “ACQUIRING” displayed on my Marantz Amplifier mean?
If “ACQUIRING” is displayed on your Marantz Amplifier, it means that the signal cannot be received. Reposition your SIRIUS Connect tuner and antenna.
Why can't I select CSII mode on my Marantz AV8003?
If you're unable to select CSII mode on your Marantz Amplifier, it's likely that the input signal is incompatible. Use a 2 channel Dolby Digital input signal, PCM input signal, or analog input signal.
Why can't I select Pro Logic IIx mode on my Marantz Amplifier?
If you're unable to select Pro Logic IIx mode on your Marantz Amplifier, it's likely that the input signal is incompatible. Use a 2 channel Dolby Digital input signal, PCM input signal, or analog input signal.
General| Pre-out channels | 7.1 |
|---|---|
| Pre-out connectivity | Yes |
| Audio output channels | 7.1 channels |
| Signal-to-Noise Ratio (SNR) | 105 dB |
| Power output per channel (20-20KHz@8 Ohm) | - W |
| HDMI in | 4 |
| Audio (L/R) in | 6 |
| Digital audio optical in | 3 |
| Ethernet LAN (RJ-45) ports | 1 |
| Number of HDMI outputs | 2 |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Audio formats supported | MP3, WAV, WMA |
| Image formats supported | JPG |
| Wi-Fi | No |
| Supported radio bands | AM, FM |
| Supported video modes | 1080p |
| Supported graphics resolutions | 1920 x 1080 (HD 1080) |
| Display | LCD |
| HDMI version | 1.3a |
| Product color | Black |
| Audio decoders | Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS-ES, DTS-HD, DTS-HD Master Audio, THX Surround EX |
| Apple docking compatibility | Not supported |
| Power consumption (standby) | 0.7 W |
| Power consumption (typical) | 85 W |
| Cables included | AC |
Weight and Dimensions| Depth | 385 mm |
|---|---|
| Width | 440 mm |
| Height | 184.5 mm |
| Weight | 11600 g |
To Next Page
