7
5. DSP(QD01) FIRMWARE UPDATE PROCE-
DURE
Necessary Equipment
•
Windows PC((Windows2000 or WindowsXP)
•
USB cable (USB 4Pin - mini USB 5pin)
•
CompactFlash (with format)
•
Update Disc (90M-PMD671CDR)
Connection
1. Connect Windows PC and PMD671 with USB cable
2. Insert the CompactFlash
Writing procedure
NOTICE : Don't turn off the power during the update. When
turn off the power, you must change Flash Rom
(QD01).
1. While pressing MARGIN RESET button, Slide POWER
switch to turn on the unit.
2. "USB ONLINE" is displayed on LCD.
3. It confi rms that it was recognized as Removable Disk
(CompactFlash) by a PC.
4. "pmd_prog.bin" of the update disk is copied to the route of
Removable Disk(CompactFlash).
5. Disconnect USB cable from the unit, then turn off POWER
switch.
6. Keep inserting the CompactFlash, turn on POWER switch.
7. DSP Firmware updating will be done automatically.
8. Light up all the LCD dot.
9. Uploading takes about one minute.
5. DSP (QD01) fi rmware
ƷǢȃȗȇȸȈ૾ඥ
࣏ᙲೞ֥
• Windows PC
Windows2000
LJƨƸ
WindowsXP
• USB
DZȸȖȫ
USB 4Pin
USB
ȟȋ
5pin
•
dzȳȑǯȈȕȩȃǷȥ
CompactFlash
ᲢȕǩȸȞȃȈฎLjᲣ
•
ǢȃȗȇȸȈȇǣǹǯ
90M-PMD671CDR
ዓ૾ඥ
1
Windows
PC
Ʊ
PMD671
ƱǛ
USB
DZȸȖȫưዓƠLJƢŵ
2
dzȳȑǯȈȕȩȃǷȥǛ
PMD671
ƴࠀƠᡂLjLJƢŵ
ǢȃȗȇȸȈ૾ඥ
ද ǢȃȗȇȸȈɶƸᩓเǛЏǒƳƍưƘƩƞƍŵᩓเǛЏǔ
Ʊ
Flash ROM(QD01)
ǛʩƢǔ࣏ᙲƕƋǓLJƢŵ
1
PMD671
Ʒ
MARGIN RESET
ȜǿȳǛƠƳƕǒ
POWER
ǹǤȃȁǛǹȩǤȉƠᩓเǛλǕLJƢŵ
2
PMD671
ƷȇǣǹȗȬǤƴ
USB
ONLINE
ƱᘙᅆƞǕLJƢŵ
3
Windows
PC
ƴȪȠȸȐȖȫȇǣǹǯ
CompactFlash)
Ʊ
ƠƯᛐᜤƞǕƨƷǛᄩᛐƠLJƢŵ
4
ǢȃȗȇȸȈȇǣǹǯƷ
pmd
A
prog
bin
ǛȪȠȸȐȖȫȇǣ
ǹǯ
CompactFlash)
ƷȫȸȈƴdzȔȸƠLJƢŵ
5
USB
DZȸȖȫǛ
PMD671
ƔǒٳƠƯᩓเǛЏǓLJƢŵ
6
dzȳȑǯȈȕȩȃǷȥǛࠀƠᡂǜƩLJLJ
PMD671
ƷᩓเǛ
λǕLJƢŵ
7
ᐯѣႎƴ
DSP
Ʒ
fi rmware
ǛƖƑLJƢŵ
8
ƜƷƱƖȇǣǹȗȬǤƸμໜ໊ƠLJƢŵ
9
᧓Ƹኖ
1
ЎDŽƲưƢŵ
mini USB 5pin