Why does nothing appear on the remote commander display of my Marantz Receiver?
If nothing appears on the remote commander display, the batteries are likely consumed. Replace all the batteries with new ones.
Why does control with the remote control unit fail on my Marantz SR4200 Receiver?
If the remote control isn't working with your Marantz SR4200 Receiver, try replacing the batteries with new ones. Make sure the remote controller's function-key setting is correct. Also, ensure you are close enough to the receiver and that there are no obstructions between the remote and the receiver.
What to do if my Marantz Receiver is not turning on?
If your SR4200 isn't turning on, make sure the power plug is securely connected to the outlet.
Why is there no sound output from the center speaker of my Marantz SR4200 Receiver?
If there's no sound from your center speaker, first ensure the speaker cable is properly connected. Check that the Surround mode isn't set to STEREO, as this mode deactivates the center speaker. If it is, switch to another Surround mode. Also, verify that 'Center = NONE' hasn't been selected in the SETUP mode; if it has, correct the setting.
Why is there no sound output from the surround speakers on my Marantz Receiver?
If you're not getting any sound from the surround speakers, check that the speaker cables are correctly connected. If the Surround mode is set to STEREO, no sound will be output from the surround speakers, so select a different Surround mode. Also, ensure that 'Surround = NONE' is not selected in the SETUP mode; correct the setting if needed.
Why is a specific channel not producing output on my Marantz SR4200?
If a specific channel isn't producing output, the issue might be with the source material. Check the encoded channel on the source side to ensure it contains audio.
Why is my Marantz SR4200 Receiver not playing a normal PCM signal (CD or laser disc)?
If a normal PCM signal (CD or laser disc) cannot be played, the Surround mode may be set to DTS. Select another mode to resolve this issue.
Why is my Marantz SR4200 Receiver not playing a Dolby Digital signal?
If a Dolby Digital signal cannot be played, the Surround mode might be set to DTS. Try selecting another mode.
What causes noise during DTS-encoded CD or laser disc play on Marantz Receiver?
If you're getting noise during DTS-encoded CD or laser disc playback, ensure you're using a digital connection and have selected digital input. The issue may arise if analog input is selected instead.
How do I stop my Marantz Receiver from playing sound and pictures from the wrong equipment?
If your Marantz Receiver is playing sound and showing pictures from equipment other than what's selected, the input cable may be connected incorrectly. Refer to the connection diagram to connect the cable correctly.
Technical specifications for the FM tuner.
Technical specifications for the AM tuner.
Technical specifications for the audio output.
Technical specifications for video input/output.
General specifications including dimensions and power.
List of accessories that come with the unit.
Explains how selected surround modes relate to input signals.
Schematic and parts location for the front PCB.
Schematic for the u-COM and key control circuit.
Schematic for the master volume PCB.
Schematic for the phones PCB.
Schematic for the power switch PCB.
Schematic diagram for the input PCB.
Schematic diagram for the video PCB.
Schematic diagram for the connection PCB.
Schematic diagram for the power supply PCB.
General| Channels | 6.1 |
|---|---|
| Dolby Decoding | Dolby Digital, Dolby Pro Logic II |
| Video Outputs | 1 composite, 1 S-video |
| Total Harmonic Distortion | 0.08% |
| Signal to Noise Ratio | 98 dB |
| DTS Decoding | DTS, DTS Neo:6 |
| Inputs | 2 digital optical, 2 digital coaxial |
| Outputs | 1 digital audio (optical) |
| Dimensions | 440 x 158 x 416 mm (W x H x D) |
| Tuning Range | FM |
| Frequency Response | 10Hz-100kHz (+1/-3 dB) |
| Input Sensitivity | 200mV |
| Video Inputs | 4 composite, 2 S-video |
| Weight | 21.6 lbs (9.8 kg) |
To Next Page
