This section must be read before any connection
is
made to
the mains supply.
•
Equipment Main Power Setting
Your Marantz product has been prepared to comply with the
household power and safety requirements that exist
in
your
area.
TT-15S1 can be powered by
120V
AC only.
•
Copyright
Recording
and
playback
of
any
material
may
require
consent. For further information refer
to
the
following:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1958
- Performers Protection Acts 1963 and 1972
- Any subsequent statutory enactments and orders
•
Do Not Locate
in
the Following
Places
To
ensure long-lasting use, do not locate the
TI-15S1
where:
•
Exposed to direct sunlight.
• Near to sources of heat such
as
heaters.
•
Highly humid or poorly ventilated.
• Dusty.
•
Subjected to mechanical vibrations.
•
On
wobbly,
inclined
or otherwise unstable surfaces
•
Radiated heat
is
blocked such as
in
cramped audio racks.
To
ensure
proper
heat
radiation,
ensure
the
below
clearance
from
walls
and other equipment.
Front
0.2m
Side
0.2m
0.2m
0.2m
•
Caution: Do not lose
the bearing.
(View from underneath the turntable chassis)
~
,'~
I
I
Turntable chassis
Center shaft
hole
Bearing
I
Center
shaft~
There
is
a bearing located inside the center shaft
hole
in
the
turntable chassis. When the turntable leaves the factory, the
center shaft
hole
is
covered with tape to prevent the bearing
from
falling
out. Sometimes after removing the tape, the
bearing falls
out when the turntable is turned over.
If
the
center shaft is inserted when there is no bearing
in
the
center shaft hole, the turntable
will
not rotate. Therefore,
make sure that the bearing does not fall
out of the center
shaft
hole
when assembling the turntable.
Furthermore,
if
the
turntable
is
disassembled
for
transportation etc. cover the center shaft
hole
with tape etc.
to prevent the bearing from
falling
out.
•
Before using
•
Thoroughly remove dust or dirt from the
stylus
point and record.
If
you
play
records when there
is
dirt/dust
on
the stylus,
not only will
the stylus have poor contact with the record
causing poor sound quality, it will also increase the rate
of wear of both the stylus and record.
Gently
remove
dirt/dust by brushing with a soft tipped brush from the
base of the stylus to the tip.
Also
wipe the record with a
good quality record cleaner.
• Install
the turntable chassis and turntable
so that they are
level.
It
is
possible to adjust the height of the
legs
by rotating
them. However, as there are
only
3 legs, the height may
not be adjustable
in
some cases.
In
such cases, adjust the rack itself so that it
is
horizontal.
•
About
howling
and hum
Howling occurs
when
sound from
the
speaker
or
vibration
is
transmitted
to
the
player
and
is
picked
up
by
the
cartridge
again.
If
howling occurs when the
volume
is
increased,
check the positions of the speakers and turntable,
and
move
them
to
locations where neither vibration nor
sound
is
transmitted
to
the
turntable.
Hum
noise occurs because
of
electromagnetic waves that are generated from other
electronic devices. Check the position
of
other electronic
devices that are near to the turntable, especially the
amplifier. Also,
hum
or noise occurs if the ground
is
not
connected correctly. Check that
the
ground wire
is
securely
connected
to
the
GND
terminal
on
the amp/mixer.
2
To Next Page
