Keep the heat gun in constant motion. Do not stop or dwell in one spot.
Use extreme caution if the opposite side of the work surface such as siding is not accessible. The
hidden side could catch re if it becomes too hot. Some buildings contain ammable material behind the
siding, oors, fascia, soft boards and other such panels. Check these areas before applying heat. Do not
use the heat gun if ammable materials are present or if you are unsure of the ammability of the hidden
material.
Do not use the heat gun near surfaces with cracks or near metal pipes, ashings, etc. Heat may be
conducted behind the work surface and ignite hidden material.
At the end of each work session, place the paint chips and dust in a double plastic bag. Close the
bag with a twist tie and dispose of it in accordance with local regulations.
Remove protective clothing and shoes in the work area to avoid transferring dust into other areas
of the building. Wash work clothes separately using a high quality detergent. Wipe shoes off with wet
rag and then wash the rag with the work clothes or dispose of it in the bag of dust and debris.
The ignition of hidden material may not be readily apparent and can cause property damage and injury.
Do not use the heat gun in the presence of ammable liquids or gases.
Do not use the heat gun near combustible materials such as dry grass, leaves or paper which can
catch re.
Do not lay the heat gun on a ammable surface during operation or immediately after turning it OFF.
The nozzle becomes very hot. Always set the heat gun on a at level surface so the nozzle is directed
upward and and away from the supporting surface.
Never touch the nozzle immediately after use. It will be very hot and can cause severe burns.
Never use the heat gun as a hair dryer. The extreme heat will burn your scalp and scorch your hair.
Always use gloves while operating the heat gun. Tools and scrapings become very hot.
Always treat the heat gun with the same respect as an open ame. It can burn you and cause a re
if not handled and used with extreme caution.
WARNING: Never operate the heat gun if the blower motor does not turn ON.
Turn the heat gun OFF immediately. Operating the heat gun without the blower motor running will burn
the element out.
SAVE THESE INSTRUCTIONS FOR REFERENCE
SAFETY GUIDELINES
10
Extension cord safety
WARNING: Keep the extension cord clear of the working area. Position the cord
so it will not get caught on the workpiece, tools or any other obstructions while you are working with the
power tool.
Make sure any extension cord used with this tool is in good condition. When using an extension cord, be
sure to use one of heavy enough gauge to carry the current the tool will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating.
The table below shows the correct size to use according to cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge. The smaller the gauge number the heavier the cord.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord or have it repaired by a qualied electrician before using it. Protect your extension cord
from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This circuit must not be less than 14 gauge wire
and should be protected with either a 15 A time delayed fuse or circuit breaker. Before connecting the
power tool to the power source, make sure the switch is in the OFF position and the power source is the
same as indicated on the nameplate. Running at lower voltage will damage the motor.
MINIMUM GAUGE (AWG) EXTENSION CORDS (120 V use only)
Amperage rating Total length
More
than
Not more
than
25'
(7.5 m)
50'
(15 m)
100'
(30 m)
150'
(45 m)
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Applicable
SAFETY GUIDELINES
11
HEAT GUN 054-1252-6
HEAT GUN 054-1252-6
To Next Page
Loading...
Need help?
General
