Maximum Controls MATRIX III MAX 1200FS PRO - Dual Gate Operators Wiring

dual gate operators wiring
Primary Operator
Secondary Operator
3UGGESTED)NPUT 3UGGESTED)NPUT
3UGGESTED)NPUT
3ENSING%DGES
#LOSING$IRECION
/PENING$IRECION /PENING$IRECION
2EFLECTOR
4HREE237IRES3EEABOVE
!#INPUT
POWER
!#INPUT
POWER
./4%4HE!LARM3HUT/FFh34/0vBUTTONCANBEPRESSEDON%)4(%2GATEOPERATOR
Alarm Shut-OFF
MOTION CONTROL
OPEN
STOP
CLOSE

5,3TANDARD-!8&302/&302/-ATRIX))))NSTALL6ERSIONB
EXIT PWR
ALARM
POWER /
SOLAR IN
BATTERY
INPUT
OPENING CLOSING
CLOSINGOPENING
ERD
OBD PORT
BLACK BOX
PROGRAMMING
SOLAR MODE
PROGRAM
MOTOR
OVER
LOAD
ERD
MOTOR
OVER
LOAD
MAX
OFF
MAX
SENSE
MAX
SENSE
BATTERY
BACKUP MODE
ERD SENSITIVITY
MOTION CONTROL
OPEN
GATE SPEED
MAG
LOCK
UL
ENTRAP
PRI
SECONDARY
LINK
STOP CLOSE
MOTOR
INPUTS
CLOSE
TIMER
MAGLOCK
DELAY
JOG
BATTERY
TEST
INPUT
ERROR
BATTERY
BATTERY
IN USE
REPLACE
BATTERY
CLOSED
LEAVE
LEAVE
OPEN
OPEN
1 TIME
BATTERY VOLTAGE
E 1/2 F
RESET /
MANUAL
RELEASE
ID
PLUG
MODULE
PORT
MOTOR
POSITION
INPUTS
SLIDER
LIMIT
SWING
LIMIT
GND
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
GND GND GND GND GND JOG RIGHT JOG LEFT TAMPER IN TAMPER NO
GATE DISABLE
MANUAL RELEASE
KEYPAD / CARD
GND (-) (+) GND GND MAX OPEN FIRE DEPT RADIO GND
RADIO SIGNAL
STRIKE CLOSE COM COM STOP OPEN
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
NO
COM
NC
ID PLUG
ERROR
24VDC OUTPUT
12VDC OUTPUT
GND
GND
GND
LOOP PWR
OFF
PRIMARY
LEFT
ON/OFF
BATTERY
RIGHT
SECONDARY
ON
QUICK
CLOSE
OPEN
LEFT
OPEN
RIGHT
GATE
OFF
1
2
3
4
5
6
7
10
8
9
1
2
3
4
5
6
MIN MIN
MAX MAX
ON
OFF 2.5 sec
1.5 sec
FAULTS
OPERATOR
MATRIX III
OFF
OFF
3
1
14
16
MIN
16
MIN
12
9
7
3
1
14 12
9
7
UL SENSOR 10K UL SENSOR N.C.
POWER
MODE A MODE B
EXIT LOOP
LOOP
LOOP
CENTER
SAFETY
GATE OPEN
COM
GATE CLOSED
MIN
MATRIX III
SWING / SLIDE
EXIT PWR
ALARM
POWER /
SOLAR IN
BATTERY
INPUT
OPENING CLOSING
CLOSINGOPENING
ERD
OBD PORT
BLACK BOX
PROGRAMMING
SOLAR MODE
PROGRAM
MOTOR
OVER
LOAD
ERD
MOTOR
OVER
LOAD
MAX
OFF
MAX
SENSE
MAX
SENSE
BATTERY
BACKUP MODE
ERD SENSITIVITY
MOTION CONTROL
OPEN
GATE SPEED
MAG
LOCK
UL
ENTRAP
SECONDARY
LINK
STOP CLOSE
MOTOR
INPUTS
CLOSE
TIMER
MAGLOCK
DELAY
JOG
BATTERY
TEST
INPUT
ERROR
BATTERY
BATTERY
IN USE
REPLACE
BATTERY
CLOSED
LEAVE
LEAVE
OPEN
OPEN
1 TIME
BATTERY VOLTAGE
E 1/2 F
RESET /
MANUAL
ID
PLUG
MODULE
PORT
MOTOR
POSITION
INPUTS
SLIDER
LIMIT
SWING
LIMIT
GND
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
GND GND GND GND GND JOG RIGHT JOG LEFT TAMPER IN TAMPER NO
GATE DISABLE
MANUAL RELEASE
KEYPAD / CARD
GND (-) (+) GND GND MAX OPEN FIRE DEPT RADIO GND
RADIO SIGNAL
STRIKE CLOSE COM COM STOP OPEN
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
NO
COM
NC
ERROR
24VDC OUTPUT
12VDC OUTPUT
GND
GND
GND
LOOP PWR
OFF
PRIMARY
LEFT
ON/OFF
BATTERY
RIGHT
SECONDARY
ON
QUICK
CLOSE
OPEN
LEFT
OPEN
RIGHT
GATE
OFF
1
2
3
4
5
6
7
10
8
9
RELEASE
1
2
3
4
5
ID PLUG
6
MIN MIN
MAX MAX
ON
OFF 2.5 sec
1.5 sec
FAULTS
OPERATOR
MATRIX III
OFF
OFF
3
1
14
16
MIN
16
MIN
12
9
7
3
1
14 12
9
7
UL SENSOR 10K UL SENSOR N.C.
POWER
MODE A MODE B
EXIT LOOP
LOOP
LOOP
CENTER
SAFETY
GATE OPEN
COM
GATE CLOSED
MIN
MATRIX III
SWING / SLIDE
Primary Operator Secondary Operator
Primary RS-485 (+) to Secondary RS-485 (+)
Primary RS-485 (-) to Secondary RS-485 (-)
Primary RS-485 GND to Secondary RS-485 GND
• AC input power run to EACH gate operator.
• Entrapment protection devices can be connected to EITHER operator.
• Normal Opening/Security/Maglock devices can be connected to EITHER operator.
• Jog LEFT/RIGHT buttons ONLY operate the specific gate connected to operator.
• Manual Release can be initiated from EITHER operator but affects BOTH operators.
• Gate Disable can be initiated from EITHER operator but affects BOTH operators.
• 6IRTUAL,IMIT0ROGRAMMINGCAN/.,9OCCURON02)-!29OPERATOR
Primary operator Matrix III settings ONLY
(settings ignored on secondary Matrix III):
• Close Timer
• Maglock Overlap Delay
• Battery Backup Mode
• Partial Open Recording
• Solar Mode
• Quick Close - Anti-Tailgate
MARY/
MARY/MARY/MARY/MARY/ARYARY/ARY/RY
OOOOKOKOKKKKK
ININLINKNNNNKNKNKK
PRIMARY/MARY/MARY/MARY/MARY/ARYARY/ARY/RY
OOOOKOK
OK
KKKK
ININ
LINK
NNNNKNKNKK
Set one operator to PRIMARY and the other to SECONDARY.
Set opening directions of each (reverse of each other).
&ORPrimary operator DIP-switch settings
ONLYREFERTOTHEDIPSWITCHTABLEON
PAGE
Event History can ONLY be viewed and/or
downloaded on PRIMARY Matrix III.
NOTE: PRIMARY board settings will override
secondary board settings if a conflict occurs.
LINK OK LEDs should remain ON indicating
good communication between operators.