Maximum Controls MAX SUPER ARM 1300 - Page 47

45
MAX Super 1300/2300 Arms V1
CH1
LLD1
LLD2
LLD3
LLD4
CH2
CH3
CH4
EARTH
JP-2
JP-1
COM - OUT
PLS OPEN
COM - OUT
PLS CLOSE
NC - COM - NO
RELAY OPEN
CONTACTS SHOWN IN ENERGIZED STATE
NC - COM - NO
RELAY CLOSE
POWER
12 - 24
VDC/VAC
O
N
1 2 3 4
MODE
OPEN
CLOSE
POWER
STATUS
RELAY
OPEN
RELAY
CLOSE
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR N.C.UL SENSOR 10K
O
R 10K
O
R 10K
O
R 10K
O
R 10K
O
10K
10K
10K
10
10
C
ENSOR
R
R
R
R
R
1
1
1
C
ENSOR
R
R
R
R
R
R
1
C
ENSO
OR
R
R
R
R
R
R
R
C
NSO
C
O
OR
R
R
R
R
R
R
R
C
NSO
C
O
O
OR
R
R
R
R
R
C
NSO
O
O
O
OR
R
R
R
R
NSO
O
O
O
O
R
R
R
SO
O
O
O
O
OR
R
SO
O
O
O
O
O
Wire to (NO) of Relay OPEN
Wire to 10K Inputs
Set both jumpers to 10K position
Typically used on SLIDE gates
Wire to (NO) of Relay CLOSE
GND
12VDC OUT Monitored
Polarity does NOT matter
10K
JP-1
Jumper
10K
JP-2
Jumper
10K Resistor Wiring to WEL-200 Wireless
EMX WEL-200 monitored WIRELESS
WEL-200R
Wireless Edge link
WEL-200T
Wireless Edge link
WEL-200T
Wireless Edge link
CLOSE
Transmitter
OPEN
Transmitter
Receiver
WEL-200T
WEL-200T
WEL-200R
The WEL-200 is a complete wireless solution for interfacing sensing edges to
gate and door operators, while ensuring compliance with UL325 monitoring
standards. Each receiver can connect with up to four transmitters with
separate relay and pulse outputs for open and close edge functionality. Each
transmitter can run for up to two years on two AA lithium batteries. With
enhanced diagnostic features, installation and maintenance for the WEL-200 is
easy and reliable. Feedback is provided for all fault modes, including edge
open, short conditions, low battery and failed transmitters.
See next page to connect reciver to transmitter.
OPEN Transmitter
CLOSE Transmitter
Receiver
WEL-200R
Wireless Edge link
Opening Sensing Edge
Closing Sensing Edge
DSP Arm Controller
47MAX Arm/Ultra Arm V1b.4
Rev 06-16-22
CH1
LLD1
LLD2
LLD3
LLD4
CH2
CH3
CH4
EARTH
10K
10K
JP1
JP2
COM - OUT
PULSE 1
COM - OUT
PULSE 2
NC - COM - NO
RELAY 1
CONTACTS SHOWN IN ENERGIZED STATE
NC - COM - NO
RELAY 2
POWER
12 - 24
VDC/VAC
O
N
1 2 3 4
MODE
RELAY 1
POWER
STATUS
RELAY
OPEN
RELAY
CLOSE
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR N.C.UL SENSOR 10K
O
R 10K
O
R 10K
O
R 10K
O
R 10K
O
10K
10K
10K
10
10
C
ENSOR
R
R
R
R
R
1
1
1
C
ENSOR
R
R
R
R
R
R
1
C
ENSO
OR
R
R
R
R
R
R
R
C
NSO
C
O
OR
R
R
R
R
R
R
R
C
NSO
C
O
O
OR
R
R
R
R
R
C
NSO
O
O
O
OR
R
R
R
R
NSO
O
O
O
O
R
R
R
SO
O
O
O
O
OR
R
SO
O
O
O
O
O
Wire to (NO) of Relay 1
Wire to 10K Inputs
Set both jumpers to 10K position
Typically used on SLIDE gates
Wire to (NO) of Relay 2
GND
12VDC OUT Monitored
Polarity does NOT matter
10K
JP-1
Jumper
10K
JP-2
Jumper
10K Resistor Wiring to WEL-200 Wireless
EMX WEL-200 monitored WIRELESS
WEL-200R
Wirele
ss Edge link
WEL-200T
Wireless Edge link
WEL-200T
Wireless Edge link
CLOSE
Transmitter
OPEN
Transmitter
Receiver
WEL-200T
WEL-200T
WEL-200R
The WEL-200 is a complete wireless solution for interfacing sensing edges to
gate and door operators, while ensuring compliance with UL325 monitoring
standards. Each receiver can connect with up to four transmitters with
separate relay and pulse outputs for open and close edge functionality. Each
transmitter can run for up to two years on two AA lithium batteries. With
enhanced diagnostic features, installation and maintenance for the WEL-200 is
easy and reliable. Feedback is provided for all fault modes, including edge
open, short conditions, low battery and failed transmitters.
See next page to connect reciver to transmitter.
OPEN Transmitter
CLOSE Transmitter
Receiver
WEL-200R
Wireless Edge link
Opening Sensing Edge
Closing Sensing Edge
DSP Arm Controller
RELAY 2
Rev 08-11-22
C