To Next PageTo Next Page
Need help?Do you have a question about the Maytag MVWC200 and is the answer not in the manual?
Details recommended spacing for recessed or closet installations, including side clearances and ventilation needs.
Specifies minimum diameter and height requirements for floor standpipe drain installations.
Details requirements for floor drain systems, including necessary kits and siphon break.
Notes that requirements for wall standpipe drains are the same as floor standpipe drains.
Outlines capacity and height needs for a laundry tub drain system installation.
Details recommended spacing for recessed or closet installations, including side clearances and ventilation needs.
Specifies minimum diameter and height requirements for floor standpipe drain installations.
Details requirements for floor drain systems, including necessary kits and siphon break.
Notes that requirements for wall standpipe drains are the same as floor standpipe drains.
Outlines capacity and height needs for a laundry tub drain system installation.
This document provides an overview of the Maytag Top-Loading Automatic Washer, covering its installation requirements and drain system options.
The Maytag Top-Loading Automatic Washer is designed to efficiently clean laundry using a top-loading mechanism. It is an automatic washer, meaning it handles the washing cycle from start to finish with minimal user intervention once the settings are selected. The washer is suitable for a variety of household laundry needs, offering convenience and performance for everyday use. Its design focuses on ease of use and reliable operation, making it a practical appliance for homes.
The washer is designed for straightforward operation. Users load laundry from the top, add detergent, and select the desired wash cycle. The automatic nature of the washer means it will proceed through the wash, rinse, and spin cycles without further input. The top-loading design can be advantageous for users who prefer not to bend down to load and unload laundry, and it often allows for adding items during a cycle.
For installation, the washer offers flexibility in placement. It can be installed in a recessed area or a closet, provided the necessary clearances and ventilation requirements are met. The document specifies recommended spacing to ensure proper operation, ease of installation, and servicing. While the washer has been tested for installation with zero clearance on the sides, allowing additional space is advised for practical reasons, such as accommodating companion appliances, walls, doors, and floor moldings, and to reduce noise transfer. If installed in a closet with a door, proper air circulation is crucial, requiring both top and bottom air openings in the door.
The electrical requirements for the washer are standard for household appliances, needing a 120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical supply. A time-delay fuse or circuit breaker is recommended, and it is also suggested to have a separate circuit dedicated solely to the washer to ensure optimal performance and safety.
The drain system offers multiple installation options to suit different home layouts. Users can choose between a floor standpipe, wall standpipe, floor drain, or laundry tub system. Each method has specific requirements to ensure efficient drainage and prevent issues like siphoning.
For a floor standpipe drain system, the standpipe needs a minimum diameter and carry-away capacity, with specific height requirements to prevent overflow and ensure proper drainage. The top of the standpipe must be within a certain height range from the bottom of the washer. If the standpipe needs to be installed higher than the maximum recommended height, a sump pump system would be necessary.
The wall standpipe drain system follows similar requirements to the floor standpipe system, focusing on the standpipe's diameter and height to ensure effective water removal.
For a floor drain system, additional accessories are required, including a Siphon Break Kit, Connector Kits, and an Extension Drain Hose, which can be purchased separately. These components are essential to create a proper siphon break and connect the washer to the floor drain effectively. The siphon break must be at a specific height from the bottom of the washer to prevent backflow and ensure the drain system functions correctly.
When using a laundry tub drain system, the tub must have a minimum capacity, and its top must be positioned within a specific height range from the floor. A critical point for both standpipe and laundry tub systems is to avoid siphoning, which means limiting the amount of drain hose inserted into the standpipe or below the top of the wash tub and securing the drain hose with a cable tie.
While the document does not explicitly detail user-performed maintenance features, the design considerations for installation indirectly support ease of maintenance. The recommendation to allow additional space around the washer, even if zero clearance is technically possible, is explicitly stated to facilitate servicing. This suggests that the design anticipates the need for technicians to access the appliance for repairs or maintenance, making it easier for them to work on the unit without obstruction.
The clear guidelines for electrical and drain system installations also contribute to long-term reliability and potentially reduce the need for frequent maintenance. Proper electrical supply prevents strain on the appliance's components, while a correctly installed drain system prevents water damage and ensures the washer operates efficiently without drainage issues. The requirement for proper ventilation in closet installations helps prevent overheating and moisture buildup, which can contribute to the longevity of the appliance.
The use of a separate circuit for the washer, as recommended, can also be considered a maintenance-friendly practice, as it isolates the appliance from other household electrical loads, potentially preventing electrical issues that could lead to breakdowns. The detailed instructions for drain hose placement and securing are crucial for preventing leaks and ensuring consistent drainage, thereby reducing potential water-related maintenance problems.
Overall, the Maytag Top-Loading Automatic Washer is designed for reliable performance with installation guidelines that support both initial setup and future servicing needs, aiming to provide a durable and efficient laundry solution.
General| Brand | Maytag |
|---|---|
| Model | MVWC200 |
| Type | Top Load Washer |
| Capacity | 3.5 cu. ft. |
| Color | White |
| Number of Wash Cycles | 11 |
| Energy Star Certified | No |
| Agitator | Yes |
| Dimensions (H x W x D) | 43.5 in x 27 in x 27 in |
