Need help?Do you have a question about the McCulloch M125-97FH and is the answer not in the manual?
General| Type | Riding lawn mower |
|---|---|
| Cutting width | 970 mm |
| Grass catcher | No |
| Cutting height | 25 - 70 mm |
| Cutting system | Cylinder blades |
| Number of wheels | 4 wheel(s) |
| Fuel tank capacity | 3.3 L |
| Recommended lawn area | - m² |
| Maximum cutting height | 70 mm |
| Minimum cutting height | 25 mm |
| Grass collecting volume | - L |
| Maximum speed (forward) | 7.5 km/h |
| Cutting clearance adjustment | 5 |
| Power source | Battery |
| Battery voltage | 12 V |
| Battery capacity | 18 Ah |
Weight and Dimensions| Depth | 2060 mm |
|---|---|
| Width | 1040 mm |
| Height | 1070 mm |
| Weight | 194000 g |
Welcome message, manual's importance for machine life and resale value.
Guidelines for driving on roads and securing the machine during transport.
Proper towing procedures and intended use of the mower on level ground.
Information on obtaining service and approved accessories for your mower.
Essential steps to perform before the machine is delivered to the customer.
Recommended maintenance after the first 8 hours of operation.
Explains essential symbols found on the machine and in the manual for safe operation.
Comprehensive safety guidelines for operating the mower safely and preventing accidents.
Warning about electromagnetic fields and their potential impact on medical implants.
Information on engine exhaust, carbon monoxide, and operating in well-ventilated areas.
Importance of operator alertness, supervision, safe environment, and avoiding fatigue/intoxication.
Rules for keeping children away and mandatory use of personal protective equipment.
Critical safety advice for operating the mower on slopes to prevent overturning and maintain stability.
Best practices for mowing, avoiding obstacles, and driving on uneven ground.
Strict rules to prevent accidents involving children near the mower.
Essential safety steps before maintenance and hazards of petrol/refueling.
Precautions for handling batteries, including acid hazards and explosive gases.
Warnings about moving parts, governor settings, and avoiding adjustments with engine running.
Guidelines for safely securing the machine for transport and adhering to road regulations.
Tips for reducing fire risk and safe handling of sharp mower blades.
Detailed diagram identifying all controls, levers, and parts of the mower.
Introduction to M105-97F and M125-97FH models and their drive systems.
Step-by-step guide for applying the parking brake on both models.
Explanation of throttle, choke, and speed limiter controls for engine and speed management.
Information on the cutting deck, blade engagement, and disengagement procedures.
How to adjust the cutting height to five different positions.
Instructions for adjusting the seat and using the cutting deck lifting pedal.
Guidelines for safely fueling the mower and important warnings about petrol.
Operation of the release control for moving the M125-97FH when the engine is off.
Steps for fitting the steering wheel and the seat to the mower frame.
Detailed instructions for attaching the cutting deck, including belt fitting.
Procedure for detaching the cutting deck for cleaning and servicing.
Instructions for fitting the mulching plug into the cutting deck.
Steps to install the side discharge chute onto the cutting deck.
How to charge the battery and connect it correctly to the mower.
Crucial checks to perform before starting the engine, including air intake and controls.
Step-by-step guide for starting the engine on both M125-97FH and M105-97F models.
Adjusting throttle for starting cold versus warm engines.
Procedure for jump-starting the mower using another vehicle's battery.
Warning against running the engine indoors due to toxic exhaust fumes.
General driving instructions, including safe gear changes and speed control.
How to lower the cutting deck and engage the blades for mowing.
Tips for extending drive belt life through proper throttle usage.
Advice on clearing the lawn, cutting heights, and mowing wet grass.
Critical warning against operating on slopes exceeding 10 degrees.
Specific method for starting on slopes with the M105-97F manual transmission.
Step-by-step guide for safely stopping the engine and engaging the parking brake.
A detailed table listing all required maintenance tasks and intervals.
Critical safety requirements that must be met before performing any maintenance.
Proper methods for cleaning the mower, with warnings against high-pressure washers.
Steps for accessing internal components by removing engine cover, front cover, and service hatch.
Instructions for lubricating the drive chain on the M105-97F model.
How to check the brake and when to seek professional help for throttle wire adjustment.
Guide to replacing the air filter to maintain engine performance.
Importance of correct tyre pressure for even grass cutting.
Steps for checking, cleaning, and replacing the spark plug.
Information on the main fuse and how to replace it safely.
Daily checks to ensure the machine's safety systems are operational.
How to ensure the engine's cooling air intake is clear of debris.
Importance of blade condition and professional sharpening/balancing.
Critical warning about the dangers of using cracked or unbalanced blades.
Procedure for checking and topping up the engine oil correctly.
Detailed steps for changing engine oil, including capacity and disposal advice.
Safety precautions when handling hot engine oil after operation.
Causes and solutions for the engine not starting or running smoothly.
Troubleshooting for engine power loss, overheating, and battery charging problems.
Identifying reasons for machine vibration and uneven mowing results.
Comprehensive guide for preparing the mower for long-term storage, including fuel stabilizer use.
Critical safety advice regarding storing fuel and machines with fuel indoors.
Recommendations for performing service during low season and ordering spare parts.
Detailed specifications for the mower's physical dimensions and operating weight.
Technical data for the engine, starting system, and electrical components.
Specifications for noise emissions, vibration levels, and transmission type.
Details on the cutting unit, cutting heights, and blade dimensions.
Statement of compliance with European directives for machinery, EMC, and noise.
To Next Page
